Recommended 5/8 Inch Hitch Pins for Mounting Lunette Ring in C-Channel Coupler
Question:
Hi, On my current trailer the lunette ring is bolted with two 5/8 inch bolts and nylock nuts to the c-channel that is welded to the trailer. I need to replace the lunette ring as it is excessively worn. Is there a reason why I have to bolt the lunette ring into the c-channel? Why can I not just use two 5/8 inch hitch pins? Looking at all the adjustable ball hitches I see the same type of geometry using basically hitch pins to hold the ball in the c-channel instead of nuts and bolts. Thanks
asked by: Bill P
Helpful Expert Reply:
For the Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D. # 337B16140Z you are correct that the 5/8 inch bolts are traditionally used for the C-channel. This is partially because the bolts are normally 5-1/2 inches long. The standard pins are simply not long enough in most cases and the lunette ring is not tested for use with these pins so you'd most likely be outside of the manufacturer's warranty.
The usable pin length of the Curt 3 inch receiver hitch pin # C21507 is 4-3/4 inches, so it will be more similar to the bolts and should work for your C-channel mount which is 3-1/2 inches outside to outside.
Products Referenced in This Question
Curt Hitch Pin and Clip for 3" Hitches - 5/8" Diameter x 4-3/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 3 Inch Hitch
- 5/8 Inch Diameter
- 4-3/4 Inch Span
- CURT
more information >
Product Page this Question was Asked From
Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D.
- Lunette Ring
- Standard Coupler
- Coupler Only
- Bolt-On
- 20000 lbs GTW
- 3 Inch Lunette Ring
- Buyers Products
more information >
Continue Researching
- Shop: Buyers Products 8 Ton Combination Hitch with Mounting Kit - 2-5/16" Ball - BH8 Series
- Shop: Buyers Products Plain 10-Ton Forged Steel Lunette Ring w/ 3" I.D.
- Shop: Buyers Products Heavy Duty Channel Bolt and Nut Kit
- Shop: Buyers Products Zinc Plated 10-Ton Forged Steel Lunette Ring w/ 3" I.D.
- Shop: Curt Bolt Kit for Flat Mount Lunette Ring
- Shop: B&W Pintle Hook Mounting Plate for 2" Hitches - 9" Shank - 8 Hole - 16,000 lbs
- Shop: Hardware Kit for Demco Adjustable Channel Mount Couplers
- Video: etrailer Adjustable Trailer Coupler - Coupler Only - CTA-400 Review
- Search Results: 10000
- Search Results: 10000 lb axle
- Search Results: lunette ring
- Search Results: 4 inch round led trailer lights
- Q&A: Optronics LED Trailer Clearance or Side Marker Light With Black Base
- Search Results: pintel hitch
- Video: Buyers Products Lunette Ring - Coupler Only - 337B16140 Review
- Video: Optronics Trailer Lights - Tail Lights - STL42RB Review
- Search Results: quick connect wire connectors
- Search Results: wire connectors
- Video: Optronics Trailer Lights - Clearance Lights - MCL13A2B Review
- Video: Optronics Mini LED Side Marker Light Installation
- Video: Optronics LED Clearance or Side Marker Trailer Light with Reflector Review
- Video: Optronics Round LED Trailer Light Review
- Q&A: Replacement for Gabriel Shock Model 610712
- Article: How to Measure a Trailer Axle
- Q&A: Taillight Converter Needed To Separate Brake Lamp and Turn Signal Circuits
- Q&A: Option to Replace Jensen JRV9000R
- Q&A: Recommended Replacement For A JVR9000R RV Stereo System With Three Cameras
- Q&A: 40' Wishbone Trailer Wiring With A Ground Wire Running Down Both Sides
- Q&A: How To Convert A Wishbone Trailer Wiring Harness To A Regular 4-Flat Trailer Wiring Harness
- Article: Tow Bar Wiring: Which Wiring Kit is for You?