Is there a Replacement Grease Zerk Fitting for a Sure Lube System
Question:
I tore the grease zerk out of the Sure Lube Grease System. The collar is round so I do not think its a screw type. It appears to be a press fit. Whats the fix? Will grease run out without the fitting? Is it safe to drive like this?
asked by: Dave M
Expert Reply:
Grease can ooze out of the opening unless you temporarily plug it with something. I would advise not to tow the trailer until you can get a new grease fitting installed. The Sure Lube manufacturer may have a specific replacement for the system.
If not then replacing the system with Bearing Buddies is the way to go. I can recommend some if you can tell me the opening size the grease caps fit into on the hub. The measurement has to be as accurate as possible so measuring with calipers such as # PTW80157 is the best way to get an accurate measurement.
Products Referenced in This Question
4" Carbon Fiber Digital Caliper
- Hand Tools
- Measuring and Layout Tools
- Digital Calipers
- Carbon Fiber
- Performance Tool
more information >
Product Page this Question was Asked From
Replacement Grease Zerk for Ram Jacks
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Grease Zerk
- etrailer
more information >
Continue Researching
- Q&A: Replacement Boat Trailer Hubs for #82655
- Video: Dexter E-Z Lube Axles Trailer Idler Hub Assembly Review and Installation
- Video: Dexter Axle Trailer Hubs and Drums - Hub - 8-213-5UC1 Review
- Search Results: timken bearings
- Search Results: 10~36 seal
- Shop: Kodiak 12" Hub-and-Rotor Assembly - 6 on 5-1/2 - Dacromet - 5,200 lbs to 6,000 lbs
- Shop: Trailer Spindle Nut 1"
- Shop: Easy Grease Trailer Idler Hub Assembly for 6K Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly - 5,200-lb E-Z Lube Axles - 12" - 6 on 5-1/2
- Shop: Bearing Kit, 15123/25580 Bearings, GS-2125DL Seal
- Shop: Trailer Idler Hub Assembly for 6,000-lb Axles - 6 on 5-1/2 - Pre-Greased
- Shop: Dexter Trailer Idler Hub Assembly for 6,000-lb Axles - 6 on 5-1/2
- Q&A: Replacement Zerk Fitting Recommendation for Dexter EZ Lube Spindle
- Q&A: 2005 Ranger Trail Boat Trailer Replacement Hub Bearings and Races for Oil Bath
- Q&A: Is It Possible to Just Replace Trailer Axle Spindle if Axle is Still Good
- Q&A: Replacement 250-031468 Seals Needed for Reliable Oil Bath
- Q&A: Upgrading From Grease Filled Hubs To Oil Filled Hubs On a 3,500LB Axle
- Q&A: Fit of Kodiak XLPROLUBE1980KIT on 3500 lb Spindles With 171255 Grease Seal
- Search Results: tongue jack
- Search Results: dexter ez lube
- Video: Performance Tool Carbon Fiber Digital Caliper Review
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Integrated Drum - AKHD-545-35-EZ-K
- Shop: Trailer Hitch
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Most Popular Wheel Bearings
- Search Results: 68149
- Shop: Fifth Wheel Hitch