Does Dexstar Steel Dual Trailer Wheel # AM20790 Require Flange Nuts

Question

Question:

Is using the ring with standard Acorn style nuts work the same as flange nuts ? The ring has tapered nut holes

asked by: Tom

1

Helpful Expert Reply:

With the Dexstar Steel Dual Trailer Wheel # AM20790 Dexstar requires the use of flange nuts in the size of 5/8"-18 like part # 95188. I can't recommend an acorn style of nut.

expert reply by: Jameson C

1

Answer 1

As long as your dual wheel has a flat surface where the Flange Wheel Nut #95188 would rest against, like what the Dexstar Dual Wheel #AM20790 has, then you would use this flange wheel nut in the place of a nut with a 90 degree cone. Attached is a…

view full answer...

Answer 2

Your tire size is compatible with a 16 inch diameter wheel that is 6 inches wide like what the trailer tire part #LHHA420 so as long as your trailer uses a dually style wheel that has an 8 on 6-1/2 inch bolt pattern this would be what you'd…

view full answer...

Answer 3

Dually wheel #LHHA420 has an offset of 5-1/2" inches meaning the mounting surface of the wheel is 5-1/2 inches outside of the center line of the wheel. This should work out well with no issues on a Kodiak disc brake set up. I also ran this…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Does Dexstar Steel Dual Trailer Wheel # AM20790 Require Flange Nuts

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching