Can Weight Distribution System Tow Trailer without Spring Bars Connected

Question

Question:

I have a 2007 keystone outback bumper pull camper. I also have a 2010 v8 f150 to pull it with. However the newly purchased preowned camper is not equipped with the pieces in the toung to attach the weight dust. bar chain and the sway bar. Can I pull it with just the ball and safety chains?

asked by: Jimmy O

0

Expert Reply:

You can tow a trailer with a weight distribution setup that does not have the spring bars connected. As long as the head of the system is attached to the shank properly (there's no reason it wouldn't be) it would work just as well as a standard adjustable ball mount.

expert reply by: Jameson C

0

Bill

7/7/2020

I lost a spring a bar while traveling. Should I continue to use the remaining Spring bar or take it off and use the hitch without the spring bars?

Reply

Chris R.

7/10/2020

I would definitely remove the remaining spring bar until you're able to replace the missing unit. If you can tell me what model system you have I would be happy to find the right spring bar.

Reply

Answer 1

The Traffic Cone Holder, #RA-26, that you mentioned is designed to store cones that are 12" - 36" tall, and the arm of the holder is 22-3/8" long. The arm does not fold down a full 90 degrees, so this would not be the best option for…

view full answer...

Answer 2

You do need a check valve to install the Hayes part #HA100400C. If you have a setup that has a primary and secondary air system you'd install the check valve between them. On older vehicles with a single air brake system, the controller should be…

view full answer...

Answer 3

I recommend looking at the Equal-i-zer Weight Dist Shank - 18" Long - 8" Rise, 4" Drop - 600 to 1,400 lbs TW #EQ90-02-4600. This is 18" long and has a max tongue weight of 1,400lbs, whereas the Equal-i-zer Weight Dist Shank -…

view full answer...

Answer 4

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 5

The 7-Way RV Upgrade Kit #ETBC7L you were looking at is exactly what you need. The yellow wire will connect to the reverse light circuit on your 2021 Highlander XLE to power the reverse lockout solenoid on your brake actuator. This kit comes with the…

view full answer...

Answer 6

Hey Zach, so we haven't had the chance to install a brake controller in a 2018 Mazda CX-9 so we don't have the wire color for the stoplight circuit switch but we can still help. The easiest is to use a circuit tester like the part #PTW2993 to…

view full answer...

Answer 7

That's actually what we recommend the most for people towing trailers with electric brakes that have tow vehicles with air brakes. Installing a P2 part #90885 will allow you to totally bypass having to interface with the air system and will work…

view full answer...

Answer 8

The Replacement Lens for RVPL5A and RVPL7A Lights #APL5AB is meant to be an exact replacement for the Optronics porch lights #RVPL5A and #RVPL7A as the title suggests. Although I cannot confirm if it would fit on the part number that you referenced,…

view full answer...

Answer 9

The wiring that comes with the 7-Way RV Upgrade Kit #ETBC7L is only meant to carry the 12V power for 1 function. Since you're wanting 12V power from your vehicle battery to go to 2 functions you need the Universal Installation Kit #ETBC7 instead.…

view full answer...

Answer 10

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 11

If you have the spring bar tension set up too high you can see ride issues. Typically it's a very harsh ride quality but sway is possible too. The best way to pick out a weight distribution system is to base it off of the loaded tongue weight of…

view full answer...

Answer 12

If you have a compatible 2-5/16" ball and shank already from your #C69JR, the replacement you need is the Curt TruTrack 2P Weight Distribution System w/ Sway Control - No Shank #C79JR. This comes with everything you need in order to mount the…

view full answer...

Can Weight Distribution System Tow Trailer without Spring Bars Connected

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching