Actual Dimensions of Timbren SES Jounce Springs in Kit TJRJK

Question

Question:

Hi, Could you tell me the dimensions of the Timbrens SES model JRJK? I’d like to make sure they’ll be within the proper clearance recommended. Thank you!

asked by: Scott F

0

Expert Reply:

Timbren rear suspension jounce spring kit # TJRJK is a confirmed fit on the 2014 Jeep Wrangler Unlimited 4WD. I went to our warehouse to measure these springs for you and found their overall end to end length is 4-1/4-inches and the diameter is 2-1/2-inches.

expert reply by: Adam R

0

Answer 1

Because the #TJRJK is a friction fit into the factory cup where the bump stop fits, a spacer wouldn't work.. If you can provide me a measurement, they might have a fit. They'll need the height difference between the underside of the frame and…

view full answer...

Answer 2

We have spacers that you can add to accommodate a 4" lift on your 2015 Jeep Wrangler Unlimited, but there are no Timbren kits available that come preset for a 4" lift. If your Wrangler Unlimited is a 4WD then I recommend going with the…

view full answer...

Answer 3

The Timbren suspension kit part #TABSJRJK that you referenced would be the correct enhancement kit for your 2018 Jeep Rubicon Unlimited but since you also have a lift kit you'll need spacers: 1/2" Spacer - #TA25722-90F00 1" Spacer -…

view full answer...

Answer 4

I have a suspension enhancement solution I can provide for your 2008 Jeep Wrangler Unlimited but the air bag style kits are not a fit with lifted vehicles. Instead you would want the Timbren kit part #TJRJK with the lift spacers #A25723-90AH00 for…

view full answer...

Answer 5

The Timbren Active Off-Road Bumpstops #TABSJRJK referenced in your question are confirmed to fit your 2018 Jeep JL Wrangler Unlimited. These are designed to replace the factory bump stops on your Jeep and will provide a stronger unit that will do a…

view full answer...

Answer 6

The Timbren Active Off-Road Bumpstops - Rear Suspension - 6,000 lbs #TABSTORSEQ are not designed for your 2016 Jeep Wrangler Unlimited. You will instead want the Timbren Active Off-Road Bumpstops - Rear Suspension - 2,400 lbs #TABSJRJK which are a…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Actual Dimensions of Timbren SES Jounce Springs in Kit TJRJK

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching