What is the Torque Spec for the 2" Hitch Ball That Comes with the Curt Class III Ball Mount # C45036

Question

Question:

What is the correct torque for the nut on the 1 inch nut on the 2 inch C45036 ball???

asked by: Geoffrey

0

Expert Reply:

The 2" hitch ball that comes with the Curt Class III Ball Mount # C45036 is actually pre-torqued so you don't have to worry about torquing it.

expert reply by: Jon G

0

Answer 1

When you are hardwiring a trailer brake controller like the Prodigy P2 #90885 the red wire connection that provides the triggering signal to the controller should be made to the wire on the COLD SIDE of the brake light switch circuit. This is the…

view full answer...

Answer 2

The SportRack Pop-Up Camper Roof Rack #SR1020 is an excellent roof rack that is confirmed to fit your 2017 Forest River Rockwood Freedom Camper 2318G. The weight capacity is 200lbs which is higher than most roof racks on the market. The square bars…

view full answer...

Answer 3

For pop ups like your 2015 Rockwood Freedom 2318G the SportRack Pop Up roof rack part #SR1020 is a really great option. I attached a link to the install instructions on this page for this rack as well as a picture that shows it installed as well.

view full answer...

Answer 4

Yes. You can use a drop ball mount like the #C45336 with the Patriot Hitches #PH54FR to get to your 16" drop total. 5" drop ball mounts are very uncommon, so a 6" like mentioned above and raising the receiver in the Patriot mount will…

view full answer...

Answer 5

The difference is the color of the pin and clips of the two kits. The Patriot Adjustable Hitch Adapter part #PH67SR has black pin and clips whereas the #PH54FR has red ones.

view full answer...

Answer 6

We don't have a combo of the Curt Hitch Ball #C40008 and Curt Ball Mount #C45340. The ball mount is extremely heavy-duty, rated up to 17,000 pounds. I think it's safe to assume you don't have a torque wrench rated up to 450 foot pounds…

view full answer...

Answer 7

What you need is a taller weight distribution shank so that you can move the head of the system up higher and get the additional height needed. For that the Curt part #C17123 which would give you additional height.

view full answer...

Answer 8

The Replacement Shank for Gen-Y Adjustable Ball Mount part #325-GH-304 is my recommendation on an adjustable receiver used for flat-towing. It will provide up to a 7-1/2" rise or drop depending on configuration.

view full answer...

Answer 9

There is not a maximum capacity for the Adjustable Drop Hitch Receiver Adapter #PH54FR. It has a 7,000 lb towing capacity and 700 lb tongue weight capacity no matter what. We have verified this with Patriot Hitches.

view full answer...

Answer 10

I wouldn't say one type of ball mount has more or a reputation of failing than the other. The welded on triple ball mount part #BWBMTT31004 that you referenced is very well made and would not have any issues with reliability.

view full answer...

Answer 11

If I am following you correctly, I think what you are looking for is a drop hitch that has a 2.5" shank for your truck and then the part that drops is a 2" receiver. So essentially a hitch reducer that also supplies a drop. If that is…

view full answer...

Answer 12

I have another option for you, but while the Patriot Hitches Adjustable Drop Hitch Receiver Adapter #PH54FR would allow you to install your current ball mount with provisions for two friction sway control, it has not be tested for this at this time…

view full answer...

What is the Torque Spec for the 2" Hitch Ball That Comes with the Curt Class III Ball Mount # C45036

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching