Hitch Ball Size on 5th Wheel to Goosneck Trailer Adapter

Question

Question:

On the fifth wheel conversion to gooseneck, is the ball size 2-5/16.

asked by: William E

0

Expert Reply:

Are you referring to an adapter to tow a gooseneck trailer with fifth wheel rails like the Curt Spyder # 16085? If so then yes, the hitch ball is a standard 2-5/16 inch gooseneck ball.

If I'm misunderstanding what you're asking, or you have a specific product you're asking about, let me know so I can get you the correct answer.

expert reply by: Charles S

0

Answer 1

So you have a gooseneck trailer and truck with a set of fifth wheel rails installed? Is that correct? For that we have the part #16085 which will fit your fifth wheel rails and provide you with a gooseneck ball for the trailer to connect to. If you…

view full answer...

Answer 2

The HydroMax RV Fresh Water Pump #P25201 referenced in your question works as a direct replacement for a 3-gallon-per-minute (GPM), 12V pump. Based on my research, it looks like your existing Shurflo 2088-403-144 pump features these same specs so it…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Hitch Ball Size on 5th Wheel to Goosneck Trailer Adapter

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching