Dimensions of Junction Box of Epicord 7-Way Molded Trailer Plug with Junction Box 277-000141

Question

Question:

what is the dimensions of this box?

asked by: Tony

0

Expert Reply:

The width of the junction box of the # 277-000141 is 3-1/4 inches, the height is 2-1/4 inches and the length is 7 inches.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Trailer wiring color codes can vary greatly so I have a solution for you, but I can't tell you which color wire goes where on your trailer for wiring up a new 7-way. However, you may look around the wiring junction box or pin box of your trailer.…

view full answer...

Answer 2

The Epicord 7-Way Molded Trailer Plug with Junction Box #277-000141 does have 12 gauge wire, which is appropriate. It can also be 10 gauge, however; either would be fine. I've added a pair of links to video reviews of this product for you to take…

view full answer...

Answer 3

The #WG54006-046 that you referenced does follow the color code chart that you attached a picture of.

view full answer...

Answer 4

The wires of the connector on the part #WG54006-046 are sealed and there isn't a way to remove them. If you check out the diagram I attached, you can see how the pins of the connector are organized.

view full answer...

Answer 5

If there happened to be a 12 volt keyed power source in the circuits of the #277-000141 you could use it for the isolation solenoid #PK5231201. Essentially you would need to have the 12 volt circuit of the vehicle already be only active when the key…

view full answer...

Answer 6

The Pollak circuit tester #PK12741 will tell you which functions are working in a 7-Way trailer connector but it doesn't tell you the location of the functions within the connector. But I can tell you that. If you are looking at the face of a…

view full answer...

Answer 7

Stretching the 7-Way Trailer Connector #WG54006-043 to 6 feet isn't the best option for you. It'll reach 6 feet but the coils are fairly tight. I extended it easily to about 4 feet but beyond that it wanted to fight me. It'll loosen up…

view full answer...

Answer 8

The auxiliary or back-up wire on a 7-way trailer connector like #HM20041, is used to power to things like interior trailer lights or other 12V accessories. It can also be used to power backup lights, but not many trailers are equipped with those.…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Dimensions of Junction Box of Epicord 7-Way Molded Trailer Plug with Junction Box 277-000141

Product Page this Question was Asked From

Continue Researching