How Long are the Anchors and Screws for Mounting Hardware for Tow-Rax Removable Wheel Chock

Question

Question:

For this mounting hardware in wood - Mounting Hardware for Tow-Rax Removable Wheel Chock - Wood Floor Item # TWSPWFKW - how thick does the wood need to be how long are the pieces that screw into the wood floor?

asked by: Jeff K

0

Expert Reply:

The part # TWSPWFKW comes with screws and anchors that are 1 inch long. Ideally your floor thickness would be right at 1 inch thick.

expert reply by: Jameson C

0

Answer 1

I spoke to my contact at Tow Rax and she told me that to install the Mounting Hardware #TWSPWFKW you will have to use a 3/8 inch drill bit and they are the screws and anchors are 1 inch long. There is no wood that comes with this hardware kit.

view full answer...

Answer 2

Good news, since the bracket requires you to drill your own holes wherever you may need them, the #TWSPWFKM hardware kit will work as long as you have a metal floor. You will need a 7/16 inch drill bit to drill the initial hole. Alternatively, if you…

view full answer...

Answer 3

The Tow-Rax Removable Wheel Chock #TWSPWC3BT can be installed on either wood or metal surfaces using the hardware kit part #TWPH2770. You will need a drill with 7/16-inch bit for wood floors or a 9/16-inch bit for metal floors as well as a 3/16-inch…

view full answer...

Answer 4

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 5

I recommend you only consider an inverter type generator. From the specs available to me online, your 2019 Forest River Salem 30KQBSS Travel Trailer is a 50-Amp service with 2nd A/C Prep option. If you have have the second AC unit installed or a…

view full answer...

Answer 6

It's good to know the Redline 2-Way Pop-Up Roof Vent #9106-2756 is finally back in style! :) There really isn't a "wrong" way to install it on a trailer but if it's raining you'd most likely want to keep it closed, or at the…

view full answer...

Answer 7

Hello Dan. Our rule of thumb is that you want at least 3" between the tire and the fender, and at least 1" between the inside of the tire and the frame of the trailer. If you need additional clearance there are ways to do this, but using…

view full answer...

Answer 8

Given the round magnet, it sounds like you have old Hayes 10 x 2-1/4 brake assemblies that have been obsolete for several years, so replacement parts aren't available any longer. Your best bet would be to replace your existing brake assemblies…

view full answer...

Answer 9

It is possible to use the cam-door lock, #383200, horizontally but it would need to be placed up higher than the midway point to reduce the amount of stress on it when the door is closed. Take a look at the picture I have included that shows this…

view full answer...

Answer 10

It is very likely the fuse if you are not getting the 12 volt auxiliary power at the 7-way of your 2020 Ram 3500, so you'll want to check your owner's manual to see where that fuse is located or your local Ram dealer can tell you. If it's…

view full answer...

Answer 11

If clearance at the wheel wells and the additional inch of height at the coupler and floor is not an issue then larger tires are a good option. Larger tires create less friction as you travel because the number of rotations to go the same distance…

view full answer...

Answer 12

We do have a wide variety of trailer tire sizes ranging from tires that fit 8" wheels all of the way up to 17-1/2" tires. When it comes to tires that fit 8" wheels your 215/60-8 tires, like part #AM1HP28, are actually going to be the…

view full answer...

How Long are the Anchors and Screws for Mounting Hardware for Tow-Rax Removable Wheel Chock

Product Page this Question was Asked From

Continue Researching