How to Get Reverse Light and Separate Turn and Stop Signals for Trailer Towing
Question:
I am looking to have the proper harness/plugs for a homemade 1976 Toyota truck bed trailer to have the tail/brake separate of the turn signal as well as the backup lights. Tow vehicle is a 2007 FJ cruiser with a 4-flat but im willing/wanting to change that to match. Thoughts? Thanks!
asked by: Paul
Expert Reply:
To start off your project you need the Hopkins Endurance 5-Way Flat Trailer Wiring Kit # HM47890 this kit includes a 5-Way for your trailer and a 5-Way for your 2007 FJ Cruiser. This will allow you to send the reverse signal to your trailer in addition to the basic trailer functions. You will need to connect the following functions to the following wires:
White - Ground
Brown - Tail Lights
Yellow - Left Turn/Stop
Green - Right Turn/Stop
Blue - Reverse
Once on your trailer side of things you just need to use the Vehicle to Vehicle Tail Light Converter # C56196 which will separate your turn and brake signals.
To make your connections you can use 16 Gauge wire # 16-1-1 and Butt Connectors # DW05744-5.
I have attached some review videos for you to check out as well.
Products Referenced in This Question
Curt 2 to 3 Wire Tail Light Converter
- Tow Bar Wiring
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal
- CURT
more information >
Deka Heat Shrink Butt Connector - 16-14 Gauge - Nylon Insulation - Blue - Qty 5
- Wiring
- Wire Connectors
- Butt Connectors
- 16-14 Gauge
- Deka
more information >
Product Page this Question was Asked From
Hopkins Endurance 5-Way Flat Trailer Wiring Kit - Vehicle and Trailer Ends - Ergonomic Design
- Trailer Wiring
- Trailer Connectors
- Trailer End Connector
- 0 - 5 Feet Long
- Plug and Lead
- 5 Flat
- Hopkins
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Wire Reverse Lights on a Trailer with a 4-Way Trailer Connector
- Shop: LED Trailer Tail Light with Grommet - Stop, Turn, Tail - 6 Diodes - Oval - Red Lens
- Shop: Blue Ox Hitch Receiver Immobilizer II - 2-1/2" Hitches
- Search Results: tc2524
- Search Results: konig
- Search Results: th2004705255
- Shop: Titan Chain Tire Chains - Diamond Pattern - Square Link - Assisted Tensioning - 1 Pair
- Shop: Konig Tire Chains - Diamond Pattern - Square Link - Self Tensioning - 1 Pair
- Shop: Tire Chains
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Shop: Trailer Hitch
- Video: Choosing the Right Trailer Wiring
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Search Results: 68149
- Q&A: How Much Slack Is Needed In Trailer Wire Connection To The Tow Vehicle?
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Q&A: Replacement Clearance Lights Needed for GLO-BRITE 122R and 122Y Lights
- Shop: Brake Controller
- Article: Stability Control for Heavy Duty Vehicles
- Shop: 7- and 4-Pole Trailer Connector Socket w/ Mounting Bracket - Vehicle End
- Search Results: dust cap
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Gooseneck Hitch
- Q&A: Installation Instructions for Bulldog Powered-Drive Kit # BD1824200100
- Video: Command Electronics Trailer Lights - Tail Lights - 328-003-6017X Review
- Q&A: How to Read the Lippert Components Axle Description Measurements