What Are Erickson Big Bed Load Extender Extension Lengths And Height Adjustment Options

Question

Question:

How far extend from hitch? What are adjustable heights?

asked by: Gordon

0

Expert Reply:

The Erickson Big Bed Junior Load Extender, Item # EM07605, extends 4 feet from hitch when used as bed extender and 11 inches when used as high mount load bar. It has five height adjustments that are in 1-3/4 inch increments and can be extended from 55-1/4 inches to 62 inches. The Load bar is also 51 inches.

I had attached a video for you to check out.

expert reply by: Brint H

0

Answer 1

Correct, the 48 inches is indeed the inside width of the crossbars on the Malone Axis Truck Bed and Roof Load Extender for 2" Hitches #MPG907.

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 5

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

What Are Erickson Big Bed Load Extender Extension Lengths And Height Adjustment Options

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching