Does the Derale Series 8000 Kit # D13503 Come with Everything Needed to Install on a 2010 Tundra

Question

Question:

Hi, I have a 2010 Tundra with the 4.6L and it came from the factory WITHOUT a tow package or cooler etc. Id like to add one and want to make sure this kit will have everything I need. Doesnt seem like the hose in the picture would be enough? Im sure there arent any hard lines in place since it doesnt currently have one. Thanks!

asked by: Lee

1

Helpful Expert Reply:

The Derale Series 8000 Plate-Fin Transmission Cooler Kit # D13503, that you referenced, comes with everything you will need to install it on your 2010 Toyota Tundra. You will simply need to cut the 4 foot hose in half (or whatever lengths you need) that comes with and connect one to your transmission cooler and the other to the return line. I have attached the installation instructions for you to check out.

If you think you will need more than 4 feet of extra hose then you can also order the Derale High-Temperature Replacement Hose # D13003.

You will want to make sure that you have enough room to mount the transmission cooler (see attached photo for dimensions). The best place to mount it is in between the grille on your Tundra and the AC condenser core for the best performance. However if you do not have enough room there you have some other options as well. I have attached a helpful article that goes into a little more detail on this for you to reference.

If you are installing this to a hard line then you may also need a compression fitting. You will just need to choose one that is compatible with the line size that you have. We have ones compatible with 5-1/6" # D13031, 3/8" # D13032 and 1/2" # D13033 lines.

expert reply by: Jon G

1

click to enlarge

Answer 1

Adding a 5th Wheel to your 2007 Toyota Tundra is not going to change your truck's towing capacity, but the hitch may have a lower rating than your truck. The rule is that you always go by the lowest rated component in the system. You can find the…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 10

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 11

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 12

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Does the Derale Series 8000 Kit # D13503 Come with Everything Needed to Install on a 2010 Tundra

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching