Could Draw Tite 63260 Fit Larger Class V Hitch of Ford Truck

Question

Question:

# BD580412 says it is a flush design for 2.5inch receivers but then it spans 4. i have a ford super duty hitch and i want to make sure it will fit since it is bigger then regular hitch sizes

asked by: Ben

0

Expert Reply:

The Draw Tite hitch lock # 63260 that you referenced has a usable span of 4 inches. If you measure the outside width of your hitch and it's less than 4 inches this will fit and work well.

expert reply by: Jameson C

0

Answer 1

The Buyers Products adapter #337RTA302 is the only one that goes from a 3 inch hitch down to a 2 inch and works with your F-250. When using the adapter though the hitch is limited to 1,200 pounds tongue weight and 12,000 pounds gross trailer weight.…

view full answer...

Answer 2

The manufacturer does not list weight capacities for the Draw-Tite Trailer Hitch Receiver Lock #63259, but it is rated for use with the 3" Reese Super Titan hitch so it would match or exceed the hitch's 25,000 GTW and 4,000 TW capacities.…

view full answer...

Answer 3

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 6

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 7

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 8

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

We do carry electric brake assemblies as well as hub/drum assemblies. To determine the correct fit, you will need to measure the spindles of your axles. I've attached a photo to assist with the measurement locations, and recommend using a digital…

view full answer...

Could Draw Tite 63260 Fit Larger Class V Hitch of Ford Truck

Product Page this Question was Asked From

Continue Researching