Jack Recommendation to Replace Shelby Jack 5754A on Trailer

Question

Question:

Hi, looking to replace a jack for a snowmobile trailer. Shelby model # 5754A rest is scratched off. Capacity 850 #’s. Was hoping to just snap ring connect to the old bracket that is welded on. Thanks

asked by: Rick

0

Expert Reply:

We did have a customer come back and say that the Fulton jack part # FTJ120W0301 will attach just fine to the pipe mount on the trailer frame where a Shelby jack just like yours was installed.

expert reply by: Jameson C

0

Answer 1

I spoke to my contact at Dutton-Lainson and was able to confirm that the Pull Pin, Easy Swivel Trailer Jack with 6" Wheel part #DL22457 for 10" lift or part #DL22560 for 12" lift is a direct replacement for the jack you have on your…

view full answer...

Answer 2

The wheel you described was for an Atwood jack and the replacement is no longer available. With this odd size jack, we don't have any compatible replacement, so I recommend replacing your jack. If you have an A-frame trailer then I recommend the…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Jack Recommendation to Replace Shelby Jack 5754A on Trailer

Product Page this Question was Asked From

Continue Researching