Replacement Center Cap Plug Trailer Wheel Cap

Question

Question:

center cup plug size hole 23/4 Were can find this size

asked by: Jesus

1

Helpful Expert Reply:

We do not carry a trailer wheel center cap plug that is 2-3/4 inches in diameter. I recommend replacing the entire center cap for a much easier fit. Do you know the pilot diameter of your trailer wheel?

I've attached a link to the page of all of our current cap and cap plug options.

expert reply by: Jason S

1

Answer 1

The pictures of the Trailer Wheel Center Cap Plug, #CCP-60C, will appear to be a different size on different computer monitors and different screen resolutions. To determine if this cap is a suitable replacement you will need to compare the…

view full answer...

Answer 2

Since you mentioned 2-3/8 inches (2.375) as the inside diameter it is likely that you need the Grease Caps #RG04-080 which has an outside diameter of 2.441 inches. The best way to find exactly what cap you need is by measuring your hub bore with a…

view full answer...

Answer 3

As you mentioned the Trailer Wheel Center Cap Plug - Chrome #AM90082 is not a fit with a 2-1/16 inch diameter. The closest we will have is #CCP-60C with a 2-3/16 inch diameter, so I recommend replacing the entire cap. We have the Trailer Wheel Center…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Replacement Center Cap Plug Trailer Wheel Cap

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching