Install Instructions and Video for Curt hitch # 13535

Question

Question:

I have lost the instructions. are the torque values listed there? Install video?

asked by: Glenn

0

Expert Reply:

I attached a link to the install instructions down below which have the torque values listed as well as an install video that will walk you through the entire install process on a 2006 Honda Pilot.

expert reply by: Jameson C

0

Answer 1

For the Draw-Tite hitch #76182 we have not yet had a local customer bring in their 2018 Forester for an install so in order to give you the installed height dimension I went to our warehouse and took a measurement of this hitch. The hitch bolts to…

view full answer...

Answer 2

The best hidden trailer hitch for your 2018 Subaru Forester is the Draw-Tite #76182 because of its strong steel construction which gives it a 525 lb tongue weight capacity (the most among hidden trailer hitches that fit an '18 Forester).…

view full answer...

Answer 3

The Curt Trailer Hitch Receiver part #CU64FR is going to be very similar to the Draw-Tite Max-Frame Trailer Hitch Receiver part #76182 which are both fits for a 2017 Subaru Forester. In regards to the Draw-Tite, the distance from the ground to the…

view full answer...

Answer 4

We have the Draw Tite hitch part #76182 which is a confirmed fit for your 2018 Subaru Forester which would be our most hidden option. It will only have the opening of the hitch visible below the rear bumper which will give you the least visible…

view full answer...

Answer 5

I attached a picture that shows what the Draw Tite hitch part #75876 looks like when installed (first picture). The flanges on the sides of the hitch are the portion of it that sticks down the furthest. And since most driveway entrances are at an…

view full answer...

Answer 6

For your 2016 Subaru Forester, the installation instructions for the Curt Class III Trailer Hitch #C13144 never say to reinstall the heat shield over the exhaust, which is why it is not shown in the video. If you'd like to reinstall the heat…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Install Instructions and Video for Curt hitch # 13535

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching