Will the Pack'Em Ladder Rack Fit a Trailer With High Side Walls

Question

Question:

Hi I am looking into buying a ladder rack for my 5x10 wooden high side trailer and was curious if either one of these products would fit my needs. Will either one of these fit on a high side trailer? Item # PK-28WL2-BMH Item # PK-28WL-BMH

asked by: Justin

0

Expert Reply:

The Pack'Em Ladder Rack for Side Rail of Open Air Trailer part # PK-28WL-BMH for 1 ladder or part # PK-28WL2-BMH for 2 ladders are universal ladder racks designed to fit most open air trailers. The only requirement for the ladder rack is that you have two anchor points for the uprights to attach to the side walls of the trailer. The upright posts will attach to trailers with metal or wooden side walls.

I went out to our warehouse and measure the bolt hole spacing on the upright posts for you The distance from the first bolt hole to the second bolt hole is 8" and 14-1/4" from the second to the third. You can see the dimension in the attached photo.

expert reply by: Conner L

0

click to enlarge

Answer 1

The Pack'em Ladder Rack for Side Rail of Utility Trailer - 2 Ladder #PK-28WL2-BMH should have absolutely no issues holding the Little Giant Ladder as well as a 23 foot long Gorilla Ladder. However, with as wide as these to ladders are, they will…

view full answer...

Answer 2

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

The crank handle for the Lippert Components Spare Tire Winch with Offset Cable item #LC159056, is Replacement Crank Extension for Lippert Spare Tire Winch Assemblies - 35-1/2" item #LC1315411. The Spare Tire Winch item #LC159056 has a 1/2-inch…

view full answer...

Answer 9

There are going to be two parts to the handle that you will need to operate the Lippert Components Spare Tire Winch part #LC159056. The first of which is the intermediate shaft or what Lippert calls a Crank Extension part #LC1315411. This will be…

view full answer...

Answer 10

The Replacement Crank Extension for Lippert Components Spare Tire Winch Assemblies #LC1315411, which is a replacement for Lippert Components Spare Tire Winch with Offset Cable #LC159056, has an inside diameter of 0.50 inches and the hex has a 0.75…

view full answer...

Answer 11

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 12

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Will the Pack'Em Ladder Rack Fit a Trailer With High Side Walls

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching