Frame Bracket Recommendation for Equal-I-Zer Weight Distribution System

Question

Question:

Hi, I have ano equalizer on one of my trailers. Can I buy just the brackets for another trailer so I dont have to buy another whole set? Thanks!

asked by: Wayne K

0

Expert Reply:

We have just what you'd need. For the frame brackets of an Equalizer weight distribution system we have the part # EQ95-01-5600 which you could mount on your second trailer.

expert reply by: Jameson C

0

Answer 1

The benefits of an Equal-I-zer hitch over the e2 is primarily the improved 4-point sway control of the Equal-I-zer. The 4-point sway control utilizes steel on steel friction at the arms as well as in the hitch head to stop sway. The e2's…

view full answer...

Answer 2

Yes, the Replacement Sway-Control Bracket for Equal-i-zer Weight Distribution #EQ95-01-5600 is rated for 6,000 lbs - 14,000 lbs Gross Trailer Weight. I have attached a review video that you can also check out.

view full answer...

Answer 3

We do indeed carry replacement brackets for the Fastway e2, like #FA94-00-0800. If all you need is the L bracket, use #FA93-02-5150. The outer link plate is also available as part #FA93-02-5350 and the inner plate is part #FA93-02-5200. The hardware…

view full answer...

Answer 4

The Replacement Sway-Control L-Bracket for Fastway e2 Weight Distribution Systems - 6,000 to 12,000 lbs #FA93-02-5150 is the same for both size systems you referenced. If you are upgrading your bars or just replacing a bracket you will be good to go.…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 11

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Frame Bracket Recommendation for Equal-I-Zer Weight Distribution System

Product Page this Question was Asked From

Continue Researching