Brake Controller Recommendation to Bypass Integrated Brake Controller of 2011 Ram 2500

Question

Question:

I am wanting to purchase a new brake box for my 2011 Ram 2500. My factory one is only putting out 3.5 volts the the pin at the back of the box and by the time it gets to the rear of the trailer to the brakes the voltage shows im ponly getting 2 volts. I want to purchase an aftermarket box that is plug and play. Also I have read that i may have a message on the evic can you tell me two good options and what to do as far as fooling the evic or do you offer a product that plugs in and does it all. thanks for the advice and if you can attach a video for the install that would help. Thank you. future customer

asked by: Dustin

0

Expert Reply:

You can bypass the factory brake controller on a 2011 Dodge Ram but there are a few things to do first. I have explained it below and also included a link to an FAQ that will help.

To install an aftermarket brake controller on a 2011 Dodge Ram that has the factory integrated controller you will have to disconnect the ITBM (Integrated Trailer Brake Module). Doing so will turn on a warning lamp on the instrument cluster. In order to disconnect the ITBM and not get the warning lamp, your local Dodge dealer will have to reconfigure the TIPM (Totally Integrated Power Module), of the truck. Once the TIPM has been reconfigured, and the ITBM has been unplugged, you can use a vehicle specific brake control harness such as the Tekonsha # 3021-P, to install the aftermarket brake control.

To disconnect the ITBM, you or the dealer will need to contact the Business Center to remove the sales code (XHC). The TIPM will need to be reconfigured. Once the sales code has been disabled you can disconnect the ITBM electrical connector, under the dash, without getting the warning lamp. Basically the computer needs to be told that the truck does not have a brake controller so you can unplug it without getting that warning light.

Then to install an aftermarket brake controller I recommend the Tekonsha P3, # 90195. This is a reliable controller that is easy to set up and use and is compatible with electric and electric over hydraulic braking systems. Use wiring harness # 3021-P. This adapter plugs into the 4-pin connector on your vehicles built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.

expert reply by: Jameson C

0

Answer 1

You can bypass the factory brake controller on a 2011 Dodge Ram but there are a few things to do first. I have explained it below and also included a link to an FAQ that will help. To install an aftermarket brake controller on a 2011 Dodge Ram that…

view full answer...

Answer 2

The Tekonsha Prodigy P3 Brake Controller, #90195, does not have an on and off switch. It will go into sleep mode after several minutes of no activity. The power draw when it is in the sleep mode is so negligible that it will not discharge the…

view full answer...

Answer 3

The SC code displayed on an integrated brake controller of a 2011 Ram 3500 indicates that you have a shorted output circuit on the brake controller wiring. If the code shows all the time then the issue is on the truck side of the wiring. If…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

The first thing you will need for your 1999 D250 is a 4-way. The Curt T-Connector Vehicle Wiring Harness #C55317 plugs into the connection points behind your rear bumper and will allow you to power your trailer's signal lights. Once the 4-way is…

view full answer...

Answer 9

If you have a vehicle specific wiring harness for a brake controller then that would indicate that you have a factory tow package and subsequently would already have a 7-way at the back of your vehicle. The universal 7-way connector #ETBC7 is meant…

view full answer...

Answer 10

There is a trailer hitch receiver as well as a 4-way wiring harness that fit your 2022 Jeep Grand Cherokee WL; that said, we don't have any way to reference a VIN so you'll need to confirm if you do have the WL, which is the new model of…

view full answer...

Answer 11

For your 2024 Hyunda Santa Cruz we have the Curt 7-way kit part #C68JR that is a confirmed fit. This installs by plugging into a factory wiring connector on your vehicle which means a really easy install that doesn't require any splicing.

view full answer...

Answer 12

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Brake Controller Recommendation to Bypass Integrated Brake Controller of 2011 Ram 2500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching