Recommended Water Pump Replacement For 2006 Fleetwood Prowler Travel Trailer

Question

Question:

I have a 2006 prowler and I need to replace the water pump. Current one is a surflow

asked by: Lynn S

0

Expert Reply:

For your 2006 Fleetwood Prowler, I recommend the HydroMax RV Fresh Water Pump - 12 Volt - 3 Gallons Per Minute - 55 PSI # P25201. This will give you a self-priming direct factory replacement for 3 GPM, 12V DC demand pumps. It can be mounted in any position and have protection against overload. It also has a built-in check valve to prevent backflow.

expert reply by: Jason S

0

J F.

5/7/2020

Where was that water pump located? I have a 2005 Prowler I need to find and replace:/

Reply

Chris R.

5/11/2020

The water pump is likely somewhere near the main water tank on your Prowler. If you're not sure where that is, you can locate the fresh water spout (from which you fill the tank) on the outside of your trailer, and then from there follow to the tank and locate hoses that you can use to track down the pump. You can also try contacting the trailer manufacturer and they should at least be able to tell you its general location.

Reply

Answer 1

I definitely understand how safety chain capacities and determining exactly what chain rating you need for your trailer can be a bit confusing. To keep it as simple as possible, safety chain requirements state that the breaking strength of EACH…

view full answer...

Answer 2

The Dometic RV Water Heater part #DMC74FR would be a great option to replace your current Atwood 6 gallon water heater as it is essentially a clone of what you have now. This uses propane as a fuel source to heat the water and 120 volts to ignite.

view full answer...

Answer 3

What you will need to do is compare look at the Tongue Weight (TW) of the trailer hitch receiver that is installed on your 2016 Acura MDX. Using a Dual Hitch Extender, like the Malone #MPG544 will reduce the TW capacity of your hitch receiver by 50%.…

view full answer...

Answer 4

I have just the rack for you. The Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount #HLY64FR is approved to use on a camper with a 2" hitch. It has a weight capacity of 80 pound each and attaches at the…

view full answer...

Answer 5

The HydroMax RV Fresh Water Pump #P25201 that you referenced will work great as a replacement for your Shur Flo part 2088 403 144. This has the same specs at 3 gallons per minute so it is a perfect replacement that will be as reliable as the Shur…

view full answer...

Answer 6

At the rear of a trailer or RV the ride quality is very rough when compared to the ride quality at the rear of a passenger vehicle. Reason being the suspension isn't as sophisticated and there is a longer distance between the rear axle and the…

view full answer...

Answer 7

The Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes #HLY64FR is rated for for motorhome towing and flat towing so you could place it in your dual hitch receiver or on the back of your vehicle if it has a 2" receiver.

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Recommended Water Pump Replacement For 2006 Fleetwood Prowler Travel Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching