Finalizing Connections for the Electric Trailer Brake Controller on a 2010 Chevy Tahoe
Question:
I have the 4 wire bundle from under the dash. The battery or hot wire is has no power. What do I look for???
asked by: Robert C
Expert Reply:
It is possible that you will need to make a few connections under the hood of your 2010 Chevy Tahoe in order to power some of the brake controller and 7-Way functions.
Under the hood, remove the cover for the power distribution box, located on the drivers side. The ring terminal for brake controller power is located directly to the right of the power distribution box. It is taped to a wiring harness between the driver-side front fender and the power distribution box. Cut the tape to release it from the harness. Then run the wire to the front of the power distribution box and hook the ring on the left post with an M6 stud, # 185916.
The ring terminal for the 12-volt power lead for the 7-way trailer connector is located to the left of the power distribution box. It is taped to a wiring harness under the power brake booster. Cut the tape to release it from the harness. Then run the wire to the front of the power distribution box and hook the ring on the right post with an M8 stud, # 185917.
Tighten the ring terminals onto the posts using nuts. Activate the brake controller power post by inserting an automotive style 30-amp fuse into the correct slot in the power distribution box. Activate the 12-volt power lead post by inserting an automotive style 40-amp fuse into the correct slot in the power distribution box.
Most vehicles are already equipped with the fuses listed above. However, if your vehicle does not have one or both fuses, you will need to insert your own fuses. Place the cover back onto the power distribution box, and close the hood to finish. I have included a link to an FAQ article that covers the above application. You will want the section called Finalizing Connections for the Brake Controller.
Products Referenced in This Question
Zinc Plated Hex Flange Nut - M6
- Accessories and Parts
- Trailer Brake Controller
- Hardware
- Nuts
- Hex Nut
- Flint Hill Goods
more information >
Zinc Plated Hex Flange Nut - M8
- Accessories and Parts
- Trailer Brake Controller
- Hardware
- Nuts
- Hex Nut
- Flint Hill Goods
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How to Activate Trailer 12V Power Feed on Factory 7-Way in 2016 Silverado
- Q&A: Finalizing Final Under Hood Wiring Connections for Brake Controller on 2009 GMC Sierra
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Wiring Diagrams
- Article: Brake Controller Installation: Starting from Scratch
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Recommended 16' Mesh Tarp for Dump Trailer
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Best Camper Jacks
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Wiring Diagram for Bargman 7-Way RV Style Connector # WG54006-043
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)