Is Ball Mount Included with Trailer Hitch Receiver # C11127?
Question:
This item include the ball mount? C11127
asked by: Alan S
Expert Reply:
The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11127 is a confirmed fit for 2012-2015 Mazda 5 models. It does come with pin and clip, but the ball mount is sold separately. For a ball mount, I recommend the Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs # C45520. You will also want a hitch ball like # C40001 for a 1-7/8 inch or # C40018 for a 2 inch.
For your vehicle trailer connection, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118520. This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access the harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse. I've attached a video to help and have also attached an article to assist in routing that power wire to the battery.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-5/8" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- CURT
more information >
2" Hitch Ball - 3/4" Diameter x 2-1/8" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 2-1/8 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- CURT
more information >
Curt Drawbar for 1-1/4" Hitches - 3-1/8" Rise - 9-1/4" Long - 3,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Rise - 3 Inch
- Fits 1-1/4 Inch Hitch
- 3500 lbs GTW
- Class II
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose a Hitch-Mounted Bike Rack
- Q&A: Lock Kit Recommendation for Thule T2 Classic Bike Rack
- Article: How Much Solar Power Do I Need For My RV?
- Q&A: Trailer Hitch Receiver and Wiring That Fits 20203 Mercedes-Benz GLE 53 AMG
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Trailer Hitch Receiver and Vertical Bike Rack Recommendation for 2013 Mazda5
- Q&A: How to Enlarge Access Holes to Install Curt Hitch # C11127 on a 2012 Mazda 5 w/o Die Grinder
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is a Drawbar and Why Would I Need One?
- Article: What Do I Need To Tow A Trailer?
- Q&A: Comparing Draw-Tite and Curt Trailer Hitch for 2018 Mazda CX-5
- Article: Trailer Hitch Receiver Sizes
- Article: Rooftop Cargo Carriers