What Vehicle Wires Are Used When Installing Trailer Connector On 2016 Cadillac XTS

Question

Question:

cant figure our what wires in car to connect my curt kit

asked by: Keith K

0

Expert Reply:

You can use the circuit tester to identify the wires you'll need to connect to the Curt Powered Tail Light Converter # C59236.

Have someone sit in the driver seat and run through the functions while you test the wires at the rear of the vehicle. In the instructions the wires can be found behind the tail light housing on each side of the vehicle. You will then attach the included converter as follows:
Converter Brown Wire: Tail Light Circuit
Converter Yellow Wire: Left Turn Circuit
Converter Red Wire: Brake Light Circuit
Converter Green Wire: Right Turn Circuit
Converter Black Wire: Positive Side of the Vehicle's Battery

Then attach the eyelet on the White ground wire to a clean bare metal surface at the rear of your XTS.

expert reply by: Jeffrey L

0

Answer 1

Congrats on your vehicle purchase! A complete towing package includes a trailer hitch receiver, wiring, a ball mount, pin and clip and a ball. For your 2015 Cadillac SRX AWD I recommend going with the Draw-Tite Max-Frame Trailer Hitch Receiver…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

What Vehicle Wires Are Used When Installing Trailer Connector On 2016 Cadillac XTS

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching