Overall Width of TorkLift GlowStep Camper Scissor Steps w/Landing Gear TLA7802-8000

Question

Question:

What are the outside to outside dimensions?

asked by: Jerry

0

Expert Reply:

According to TorkLift the overall width of TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 2 Steps - 20" Wide - 350 lbs Item # TLA7802-8000 is 21 inches.

expert reply by: Michael H

0

Answer 1

The TorkLift GlowStep Camper Scissor Steps w/ Landing Gear #TLA7802-8000 that you referenced uses two pretty easy to remove pins between the steps and the mounting bracket. It would be relatively pretty easy to remove and install when needed.

view full answer...

Answer 2

Installing the TorkLift GlowStep Scissor Steps #TLA7802-8000 on your truck bed camper will be similar to installing them on a trailer. The mounting bracket connects to the camper just under the doorway and the steps connect to the bracket.…

view full answer...

Answer 3

It's hard to say exactly how stable the step setup would be, but the TorkLift GlowStep Camper Scissor Steps #TLA7803-8000 that you referenced could have it's bracket attached to the bottom step of your current steps to bridge the 30…

view full answer...

Answer 4

The TorkLift GlowStep Camper Scissor Steps #TLA7803-8000 have a horizontal bar above the top step that is the mounting bracket to connect the steps to an RV. I've linked the install details that show how it's installed. There are also…

view full answer...

Answer 5

The bolts you show will work with the TorkLift GlowStep Camper Scissor Steps - 2 Steps - Aluminum - 20" Wide - 375 lbs #TLA7802. The attachment bracket will work for this application. If you want to replace the pins with locks, you can use…

view full answer...

Answer 6

Yes; there is a way to do this. In order to add a step to your TorkLift Glow Step #TLA7803 you can use the Single Add-On Step for TorkLift GlowStep Kits - 20" Long x 8" Deep #TLA7801. This adds a step in the middle and leaves the…

view full answer...

Answer 7

The Lippert Electric Tread Lite Step #LC353621 was not intended for boat trailer applications where it would get submerged. None of our powered options were designed for that. You'd have to go with a manual pull out step like the Hickory Springs…

view full answer...

Answer 8

Technically, you could install scissor steps such as #TLA7806 or #AS25 on anything that you want. However you would need to make sure that the bottom of the steps, when pulled out, makes contact with the ground because that is where half of the…

view full answer...

Answer 9

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 10

A cover being installed on your spare tire would not prevent the Swagman Bike Rack part #S80501 from installing. The rack would still fit and work well. You might still compare the dimensions in the picture I attached with you spare tire so that you…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I wish I could say yes, but as of right now they are not a fit for the 2016 models and we do not have any other suspension enhancement options. If you are trying to fight suspension sag from the tongue weight of a trailer there is a better option. A…

view full answer...

Overall Width of TorkLift GlowStep Camper Scissor Steps w/Landing Gear TLA7802-8000

Product Page this Question was Asked From

Continue Researching