TorkLift GlowStep Scissor Steps Installation on a Truck Bed Camper

Question

Question:

Installation of steps to lance truck camper

asked by: Lauri

0

Expert Reply:

Installing the TorkLift GlowStep Scissor Steps # TLA7802-8000 on your truck bed camper will be similar to installing them on a trailer. The mounting bracket connects to the camper just under the doorway and the steps connect to the bracket.

I've linked the install instructions for you.

expert reply by: Charles S

0

Answer 1

I recommend using the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide - 375 lbs #TLA7804-8000. These are a 4 step system that has glow tape on the steps to help with visibility at night, and the adjustable…

view full answer...

Answer 2

The 5 step TorkLift GlowSteps #TLA7505 could work for your 2022 Lance 825 truck camper, but require that you have an entry height of 38-1/2" to 46" of entry height. This is measured from the bottom of your door to the ground when…

view full answer...

Answer 3

It sounds like you have a set of the TorkLift GlowStep Revolution Scissor Steps but need both the mounting brackets and hardware to attach to them to your trailer. If that is the case then you are just going to want to replace the entire step as…

view full answer...

Answer 4

According to TorkLift the overall width of TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 2 Steps - 20" Wide - 350 lbs Item #TLA7802-8000 is 21 inches.

view full answer...

Answer 5

The bolts you show will work with the TorkLift GlowStep Camper Scissor Steps - 2 Steps - Aluminum - 20" Wide - 375 lbs #TLA7802. The attachment bracket will work for this application. If you want to replace the pins with locks, you can use Pin…

view full answer...

Answer 6

The TorkLift GlowStep Camper Scissor Steps #TLA7803-8000 have a horizontal bar above the top step that is the mounting bracket to connect the steps to an RV. I've linked the install details that show how it's installed. There are also two…

view full answer...

Answer 7

It's hard to say exactly how stable the step setup would be, but the TorkLift GlowStep Camper Scissor Steps #TLA7803-8000 that you referenced could have it's bracket attached to the bottom step of your current steps to bridge the 30 inch gap…

view full answer...

Answer 8

Yes; there is a way to do this. In order to add a step to your TorkLift Glow Step #TLA7803 you can use the Single Add-On Step for TorkLift GlowStep Kits - 20" Long x 8" Deep #TLA7801. This adds a step in the middle and leaves the rest of…

view full answer...

Answer 9

The TorkLift GlowStep Camper Scissor Steps w/ Landing Gear #TLA7802-8000 that you referenced uses two pretty easy to remove pins between the steps and the mounting bracket. It would be relatively pretty easy to remove and install when needed.

view full answer...

Answer 10

The Lippert Electric Tread Lite Step #LC353621 was not intended for boat trailer applications where it would get submerged. None of our powered options were designed for that. You'd have to go with a manual pull out step like the Hickory Springs…

view full answer...

Answer 11

Technically, you could install scissor steps such as #TLA7806 or #AS25 on anything that you want. However you would need to make sure that the bottom of the steps, when pulled out, makes contact with the ground because that is where half of the…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

TorkLift GlowStep Scissor Steps Installation on a Truck Bed Camper

Product Page this Question was Asked From

Continue Researching