Recommended Weatherproof Cover For Stromberg Carlson 5000 Electric Trailer Jack

Question

Question:

What waterproof aftermarket fabric cover do you sell that fits the Stromberg Carlson JET-5000 electric tongue jack?

asked by: Karl G

0

Expert Reply:

I recommend the Ultra-Fab Protective Cover for Electric A-Frame Jacks - Vinyl - 14-1/2" x 15-1/2" # UF38-944026. This vinyl cover will protect your Stromberg Carlson # Jet-5000 electric jack from UV rays, dirt, grime, and inclement weather.

expert reply by: Jason S

0

Answer 1

The Ultra Fab jack cover part #UF38-944020 is the recommended cover for the Ultra-Fab jack part #UF38-944040. This will fit the jack perfectly.

view full answer...

Answer 2

The Electric Trailer Brake Kit, #AKEBRK-35, will work with 16 inch wheels with no issues. I recommend using #AKEBRK-35-SA brake assemblies instead. These assemblies are self-adjustable which only needed an initial set-up during installation. After,…

view full answer...

Answer 3

A trailer jack is only going to be lifting the tongue weight of the trailer, maybe a little more, so it does not have to have the same or higher capacity as the gross trailer weight. On a trailer weighing in at 4,777 pounds the tongue weight at 10 to…

view full answer...

Answer 4

Yes, you can install the Stromberg Carlson Electric Trailer Jack #JET-5000 to the side rather than straight ahead. Since the bolt pattern is a 3-bolt, triangle shape it wouldn't be perfectly 90 degrees but 120 degrees instead. Yes, you can do…

view full answer...

Answer 5

We have exactly what you would need. I recommend the Stromberg Carlson Electric Trailer Jack Item #JET-5000. This jack has more than enough capacity as it is rated for 5,000 lbs of tongue weight which is much more than your 6,200 lb trailer would…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Recommended Weatherproof Cover For Stromberg Carlson 5000 Electric Trailer Jack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching