Opening Width of Valterra Double Rotating Waste Valve Outlet Item # T81

Question

Question:

How wide is this entire waste value - Valterra Double Rotating Waste Valve - 3inch Hub x 1-1/2inch Hub x 3inch Spigot Outlet Item # T81 I need this waste valve, but want to make sure that it is the same width as my old waste valve.

asked by: Kenneth F

0

Expert Reply:

The width of the smaller opening on the Valterra Double Rotating Waste Valve # T81 that you referenced is 1-1/2 inches and the width of the larger opening on the other side is 3 inches.

These sizes are the standard sizes found on RV valves so most likely the sizes would match up.

expert reply by: Jameson C

0

Answer 1

There is an extension that is longer than 5" which will work for you. The Valterra Clearview Extension #T1022 is 10" long and otherwise the same as the 5" Valterra extension you referenced. I've left a link to a video review of the…

view full answer...

Answer 2

It depends on what type of waste valve you currently have. If you have a Valterra Bladex then you can replace the waste valve body with part #T1001VP for a 1-1/2" diameter or part #T1003VPM for a 3" diameter. If you have a different brand…

view full answer...

Answer 3

Since the placement of the blank waste valve handle makes it hard to operate I recommend switching out the valve with a cable actuated valve that will allow you to place the handle exactly where you need it. The LaSalle Bristol Cable-Actuated RV…

view full answer...

Answer 4

The Valterra Bladex Waste Valve Body for RV Gray Water Tank - Plastic Handle - 1-1/2" Diameter #T1001VP is 5/8" thick.

view full answer...

Answer 5

If you're looking to replace your blackwater waste valve and cable, then I recommend going with an actuated cable valve. For these, LaSalle Bristol offers two options while Valterra offers none. Which of the two Bristols you choose will depend on…

view full answer...

Answer 6

The #T1003PBC valve is the one you will need for your sewer plumbing. We refer to it as valve body, because it does not include the handle, which you need to operate. Since you have indicated you have a 18 inch extension handle the #T1003PBC is the…

view full answer...

Answer 7

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 8

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 11

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Opening Width of Valterra Double Rotating Waste Valve Outlet Item # T81

Product Page this Question was Asked From

Continue Researching