Comparison of Curt or Draw-Tite Trailer Hitch Receiver for Carrying Bikes on a 2016 Mazda CX-3
Question:
We have a Curt Hitch on our Mazda CX-3 - when our two bikes are on the back there is a wicked amount of play and bounce on the hitch. I was wondering if the Drawtight hitch would have the same problem or is that a somewhat better design. We have the stabilizing straps but due to the rear spoiler on the car, the strap has caused a hairline split in the rear spoiler on the car. Thanks for your help.
asked by: Karen D
Helpful Expert Reply:
Both the Curt # C11418 and Draw-Tite # 24933 trailer hitch receivers install into the same location as each other on your 2016 Mazda CX-3. However, the Draw-Tite does not require the use of the support strap # 18050 like the Curt does.
Both racks are Class I, 1-1/4 inch hitch receivers so I doubt you will have a much different ride using the Draw-Tite instead of the Curt.
Have you tried an anti-rattle device on the bike rack? If you can tell me the make and model of the bike rack we may have a solution for you.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Video: Tekonsha T-One Vehicle Wiring Harness Installation - 2019 Mazda CX-9
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Q&A: Does Curt Still Require Stabilizer Strap When Carrying Hitch Mounted Accessories
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Search Results: wiring harness
- Search Results: c58000
- Search Results: curt ball mount only
- Search Results: 18140
- Search Results: 18136
- Search Results: curt trailer hitch receiver
- Search Results: cargo carrier
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Ball Mount for 2" Hitches - 4" Rise, 6" Drop - 9-1/4" Long - 7,500 lbs
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: T-One Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Q&A: Curt C11525 Hitch for 2022 Honda Accord
- Q&A: Best Trailer Wiring Harness for a 2014 Mazda CX-9 with Factory Tow Package
- Q&A: Differences Between Curt, Draw-Tite, and etrailer.com Trailer Hitches for 2019 Subaru Outback Wagon
- Q&A: 4-way Wiring Harness for a 2021 Mazda CX-9
- Q&A: Choosing Beteween Curt or Draw-Tite Class III Trailer Hitches for 2020 Mazda CX-5
- Video: Review of Draw-Tite Trailer Hitch Ball Mount - Fixed Ball Mount and 2 Inch Ball - DT49MR
- Shop: Base Plate for Tow Bar
- Shop: Roof Rack
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: How to Choose the Right Trailer Hitch Class
- Video: Choosing the Right Trailer Wiring