Dimensions Of The TruRyde Bearing And Races Kit # BK1-150

Question

Question:

what is the brg race OD? are the brg IDs 1-1/16 brg seal ID 1.25 ? OD 1.983

asked by: Jim

0

Expert Reply:

On the TruRyde Bearing Kit, part # BK1-150, the bearing race would be the TruRyde Race, part # L44610, which has an outside diameter of 1.980 inches.

The bearings are the TruRyde Bearing, part # L44649, which has an inside diameter of 1.063 inches, which is about 1-1/16 (1.062) inches.

The bearing seal is the TruRyde Grease Seal, part # RG06-020, which has an inside diameter of 1.5 inches and an outside diameter of 1.987 inches.

expert reply by: Jeff D

0

Answer 1

Your trailer looks awesome! The Road armor equalizers #LC696740 and Equa-Flex Cushioned Equalizers #LC279687 are both pretty similar in performance even though the Road Armor has two dampers. The main difference is the size of the equalizers. The…

view full answer...

Answer 2

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 3

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 4

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 7

The tires on your trailer should not come off the ground while leveling. It sounds like you just need to reset the zero point. In order to do this you will need to follow the steps I have attached for you below and in the photo. If this does not fix…

view full answer...

Answer 8

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

For your Atwood water heater number gc6aa-10e, it sounds like you have either a wiring issue or an element issue. To determine if a replacement is needed you will want to make sure the connections are good to and from your switch. I recommend using a…

view full answer...

Answer 11

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Dimensions Of The TruRyde Bearing And Races Kit # BK1-150

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching