Wire Diagram for Installing a Voyager Brake Controller on a 2002 Ford F-250

Question

Question:

I purchased a Tekonsha #9030 Voyager Brake Activator it has a black,red,white and blue wire. My 2002 Ford F-250 has a wire harness that has a red,light green,dark blue,white and brown wire. How do I wire this up?

asked by: Kevin O

0

Expert Reply:

On your 2002 Ford F-250 you will need to connect the Red wire to the Black wire on the brake controller for +12 Volts power and the Light Green wire to the Red Stoplight wire on the brake controller. The Dark Blue wire is connected to the Blue wire from the brake controller to send power to the Trailer Brakes, and the White wires are connected to each other providing a ground for the brake controller. I posted a diagram with your wire colors added to it for you, see drawing at right.

The brown wire is an illumination wire that has power when the tail lights are switched on and is not used for brake controller installation.

If you find a connector under the dash of your 2002 Ford F-250, that the Universal Brake Control Wiring Adapter for Ford, item # 3035-S, will connect to, you can use this connector, splicing like colored wires to your brake controller, and will not need to splice into the vehicle wiring you have found.

expert reply by: Robert G

0

click to enlarge

Answer 1

We do have a wiring diagram for you! Whether you have the 1,000 psi Dexter DX Series #K71-650 or the 1,600 psi Dexter DX Series #K71-651 the wiring will be the exact same. I have attached a wiring diagram and review videos for you to check out.…

view full answer...

Answer 2

The Curt Trailer Hitch Receiver #C15410 has a measurement of 12-1/2" from the face of the receiver to the bolt hole nearest the receiver. I have attached a picture showing the dimensions for the bolt holes as well as the receiver distance.…

view full answer...

Answer 3

A lot of RVers still use wheel chocks like Andersen Camper Wheel Chock and Leveler part #AM3604 for extra stability. The chocks will insure the tires do not move back and forth at all. They are especially helpful if you are on very unlevel ground…

view full answer...

Answer 4

On each individual electric brake magnet the amperage draw would be 3.0 to 3.2 max amps at 12 to 13 volts on 7-inch brake magnets and 3.2 to 4.0 max amps at 12 to 13 volts on 10 and 12-inch brake magnets. The max amperage draw for the brake magnets…

view full answer...

Answer 5

The Solera 18V Power RV Awning Conversion Kit - Universal - 69" Arms - White #LC434730 does use a lithium-ion battery. The Replacement is 18.5V Lithium-Ion Battery for Solera 18V Power RV Awning #LC387959 if ever needed. Lithium batteries…

view full answer...

Answer 6

Do you mean that you're using a circuit tester on your 6-way connector on the trailer (not the truck) and you're reading 12 volts on one of the pins? The only way that would happen would be if you had a battery mounted on the trailer.…

view full answer...

Answer 7

Wiring connections for the Electric Over Hydraulic Brake Actuator are as follows. Yellow - Cold side of breakaway switch, The wire that goes hot when a breakaway occurs. Black - Positive connection on breakaway switch, The wire that charges the…

view full answer...

Answer 8

It sounds like your truck will use a 7-way harness like Hopkins #40167 which uses connectors like what you describe. Please refer to the linked photo that shows those connectors. This includes a 7-way socket that plugs into the included round U.S.…

view full answer...

Answer 9

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 10

From the sounds of your question, it sounds like you have factory track OEM rails on the roof of your 2015 Jayco 1207UD Say Series camper. If this is the case, I recommend the following parts: - Rhino-Rack Roof Rack for Factory Tracks - 2 Vortex Aero…

view full answer...

Answer 11

For the channels you have on top of your 1999 Chevy Silverado the Rhino Rack Vortex Aero bars part #Y02-490B-NT would be a great option that comes with everything needed to install 59 inch aero shaped bars.

view full answer...

Answer 12

First, lets start by resetting the Prodigy P2. With the trailer disconnected from the vehicle, disconnect the brake controller by unplugging the harness from the rear of the unit, and plug it back in. The display will show NC for 15 seconds, and then…

view full answer...

Wire Diagram for Installing a Voyager Brake Controller on a 2002 Ford F-250

Featured Help Information

Miscellaneous Media

Continue Researching