Square Spindle that Trailer Hub T4084600042 Fits

Question

Question:

#TRU47FR Spindle 1.5inch SQ and T4084600042 Trailer Hub Assembly for 2,000-lb Axles - 5 on 4-1/2 - Cast - #T4084600042 Do these hubs an spindles work together? Is there another spindle like thes that is ez Lund but still square?

asked by: Mark B

0

Expert Reply:

The spindle and hub you mentioned are not compatible with each other.

For the hub part # T4084600042 the spindle you would want is the part # TRU97FR which is a square spindle like you said you were interested in.

expert reply by: Jameson C

0

Answer 1

You will want to go by the capacity of the axle/trailer and get spindles that will match. So for example if the trailer/axle is rated up to 2,000 pounds using the TruRyde spindle #TRU97FR that you were looking at would work. You will also want to…

view full answer...

Answer 2

You can use any of three spindles with the Trailer Hub Assembly - 2,000 lbs Axles - 5 on 4-1/2, item #34822545BX. I have listed these spindles below. #TRU94FR - BT8 Spindle for 2,000-lb Trailer Axles - 1-1/4" Diameter #TRU59FR - BT8 Spindle…

view full answer...

Answer 3

The modern metric equivalent to your 18.5-8.50-8 tire size is the 215/60-8 size of special trailer tire. Please refer to the linked article. We do offer two options in a pre-mounted tire/wheel product that you can see on the page linked for you.…

view full answer...

Answer 4

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 5

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

I added a photo which shows the location of the heating element of the Atwood Water Heater GC6AA-10E for you. It is item number 17 in the diagram. Atwood does recommend having a professional do the job if you are replacing it due to its location.

view full answer...

Answer 11

For your Atwood water heater number gc6aa-10e, it sounds like you have either a wiring issue or an element issue. To determine if a replacement is needed you will want to make sure the connections are good to and from your switch. I recommend using a…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Square Spindle that Trailer Hub T4084600042 Fits

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching