What Supports Bumper Fascia After Curt Trailer Hitch is Installed on a 2016 Mazda CX-3
Question:
I watch your video on how to install C11418 receiver on Mazda Cx-3. I understand that bumper support arms has to be remove and can not put back in place. Whats going to support the plastic bumper to prevent from moving?
asked by: Manny V
Expert Reply:
With Curt hitch # C11418 installed on a 2016 Mazda CX-3 the lower fascia is still attached elsewhere on the vehicle and it will also be resting on top of the hitch receiver. There isn't room to replace the brackets that were removed to install the hitch.
It does not appear to be an issue with Draw-Tite hitch # 24933 and I have linked that video for you as well.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited to 2 bikes maximum on a Class I hitch.
If you go with the Curt hitch then Curt also says you have to use stabilization strap # 18050 when using this hitch for any non-trailer load (such as a bike rack or cargo carrier) per their warranty requirements. I have linked the Class I compatible 2-bike racks and cargo carriers for you.
Products Referenced in This Question
Curt Cam Buckle Stabilizing Strap for Hitch-Mounted Accessories - 61" x 1" - Qty 1
- Accessories and Parts
- Hitch Bike Racks
- Hitch Cargo Carrier
- Tie Down Straps
- CURT
more information >
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Q&A: Best Looking Trailer Hitch for 2018 Mazda CX-3
- Q&A: Does Curt Still Require Stabilizer Strap When Carrying Hitch Mounted Accessories
- Shop: Swagman XC2 Bike Rack for 2 bikes - 1-1/4" and 2" Hitches - Frame Mount
- Shop: Kuat Transfer V2 Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount
- Shop: Yakima HoldUp EVO Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount
- Shop: Kuat Sherpa 2.0 Bike Rack for 2 Bikes - 1-1/4" Hitches - Wheel Mount - Black
- Video: Curt Trailer Hitch Installation - 2017 Mazda CX-3
- Video: Draw-Tite Sportframe Trailer Hitch Installation - 2017 Mazda CX-3
- Q&A: Does Curt Hitch 11418 Fit 2016 Mazda CX-3
- Video: Trailer Hitch Installation - 2016 Mazda CX-3
- Video: Draw-Tite Sportframe Trailer Hitch Installation - 2019 Mazda CX-3
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Video: Trailer Hitch Installation - 2016 Mazda CX-3 C11418
- Video: Best 2016 Mazda CX-3 Hitch Options
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Is 12V Power Connection Required for Tekonsha T-One 4-Pole Wiring Harness 118718 to Function
- Search Results: 4 pin tester
- Search Results: curt drawbar
- Search Results: tester 7 pin
- Search Results: locking pin
- Search Results: curt 2 ball
- Search Results: locking hitch pin
- Search Results: locking hitch pins
- Q&A: How Tall is the Ball Part Only for Curt 1-7/8 Inch Ball 40001
- Q&A: Full setup for 2017 subaru impreza hatch
- Video: Best 2016 Mazda CX-3 Trailer Wiring Options