How to Gain Clearance Between Tailgate and A-Frame Sidewind Trailer Jack
Question:
I have a tailgate clearance problem with the sidewind A-Frame jack on my trailers tongue. Its only the crank handle on the jack that interferes. I am considering replacing the jack to solve the problem. A topwind jack with a handle that would fold back would likely solve the problem but I would actually prefer the sidewind design. Do any of your sidewind jacks allow the crank to be re-oriented 90 degrees to the side or other orientation instead of being on the front of the jack? Thank you!
asked by: Aaron Y
Expert Reply:
An A-frame trailer jack like # TJA-5000S-B can be position in any orientation. So the handle can be installed facing the rear if you'd like.
Another solution that may work for you is a longer ball mount. We have the Brophy # EA40 which is 14-5/8 inches from the hitch pin hole to the ball hole. This will move the entire trailer back from the tailgate.
Products Referenced in This Question
Brophy Ball Mount - 3" Rise, 4" Drop - 14-5/8" Long - Aluminum - 8,000 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Aluminum Shank - Silver
- Drop - 4 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 8000 lbs GTW
- Class IV
- Long Shank
- Brophy
more information >
Product Page this Question was Asked From
Round A-Frame Trailer Jack - Sidewind - 15-5/8" Travel - 5,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 4001 - 5000 lbs
- Sidewind Jack
- 16 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: dual propane tank cover
- Video: Adco Propane Tank Cover for Dual 20-lb Tanks Review
- Shop: RV Covers
- Shop: Classic Accessories RV Propane Tank Cover for Dual 30-lb Tanks - Gray
- Shop: MB Sturgis Propane Pigtail w/ Back Check - RV Type 1 x 1/4" Male NPT - 1'
- Shop: Adco RV Propane Tank Cover for Dual 20-lb Tanks - White
- Shop: MB Sturgis Propane Pigtail w/ Back Check - Type 1 x 1/4" MIF - Stainless Overbraid - 1'
- Shop: Brophy Ball Mount for 2" Hitch - 3/4" Rise, 2" Drop - 13-1/4" Long - 10,000 lbs
- Shop: Bottom Support Plate for A-Frame Trailer Jacks by Dutton-Lainson
- Search Results: trailer hitch
- Search Results: extra long ball mount
- Search Results: a frame support
- Search Results: 12000 lbs electric jacks
- Search Results: trailer jack
- Search Results: coupler repair kit
- Video: Review of Ultimate Jack Trailer Jack - A-Frame Jack - 322-RDJ-2K
- Video: Ultimate Trailer Jack A-Frame Topwind Jack Review
- Shop: Ultimate Trailer Jack - A-Frame - Topwind - 27-1/2" Lift - 2,000 lbs
- Q&A: Mounting Hole Dimensions and Spacing on etrailer.com A-Frame Trailer Jack # TJA-5000S-B
- Q&A: Recommended Manual and Electric A-Frame Jacks for a Snowmobile Trailer
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Trailer Wiring
- Video: Lippert Solera Slider Slide-Topper Review
- Shop: Fifth Wheel Hitch
- Video: etrailer Class III Trailer Hitch Installation - 2016 Jeep Cherokee
on Trailer Jack
