Trailer Brakes Do Not Lock Up and Show Low Voltage, What is the Right Voltage
Question:
Vehicle: 96 Toy 4Runner, can hear brakes hum but wheel will not lock up. Have adjusted trailer brakes, and measured voltage in wire to elect brake: less than one volt, is this correct?
asked by: Ward E
Expert Reply:
I contacted our representative at Redline about the issue you are having with your trailer brakes and your 1996 Toyota 4Runner. He informed me that there should be 12 volts of power at the trailer brakes if the brake controller is putting out 12 volts.
Start with your brake controller. Review the set-up instructions that came with your controller to make sure it adjusted correctly. Then, use a multimeter like part # PT89ZR to check the voltage on the blue output wire of the controller. With the controller turned all the way up, you should get 12 volts on this wire with the manual brake switch activated.
The other thing you will want to check is the connector on the vehicle and the trailer. There could be corrosion in the connector that is preventing sufficient voltage from getting through to the trailer. You can test the voltage at the vehicle side of the connector and at the trailer side connector to see if this is the case. If so, you will need to replace the 7-way connector.
You can also test the brake magnets. I have included a link to an FAQ article that explains how to test trailer brake magnets to see if they are working properly. I will also link you to a video showing how to bench test a brake controller.
Products Referenced in This Question
Digital Multimeter with 42" Long Test Leads - LED Display
- Electrical Tools
- Testers
- Multimeter
- Yellow
- Performance Tool
more information >
Product Page this Question was Asked From
Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Manual Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: How Much Voltage Should Be Applied To Brakes on Trailer w/ Electric Brake Controller
- Article: Testing Trailer Brake Magnets for Proper Function
- Q&A: Testing for Proper Voltage on the Brake Output Circuit
- Q&A: Troubleshooting Voltage Drop to Trailer Brake Assemblies
- Video: Deka Wiring 12-2-1 Review
- Q&A: Troubleshooting Trailer Brakes With Low Voltage
- Article: Trailer Wiring Diagrams
- Shop: Jacketed 2 Wire (Brake Wire) - 12 Gauge - per Foot
- Q&A: Recommended Wire Gauge for Wiring Electric Brakes on Trailer
- Article: Trailer Drum Brakes vs. Disc Brakes: Making the Decision
- Q&A: Voltage at Brake Magnets is 8 Volts with Brake Controller Set to Maximum
- Search Results: magnet
- Q&A: Testing Trailer Brake Magnets With Full 12V Power Supplied Using the Brake Controller Override
- Shop: Replacement Magnet Kit for 10" Electric Trailer Brake Assemblies - 3,500 lbs
- Shop: 10 Gauge Primary Wire - Blue - per Foot
- Article: Testing Breakaway Systems
- Article: Testing Brake Controls
- Search Results: spring bushings
- Search Results: 24 leaf spring
- Search Results: leaf spring
- Search Results: seals
- Video: Dexter Nev-R-Adjust Electric Trailer Brake Kit Installation
- Shop: Spindle Grease Seal Set for LM48548 or L68149 Inner Bearing and 1.980, 1.968 or 2.562 Bearing Buddy
- Shop: Dexter Nev-R-Adjust Electric Trailer Brake Assembly - 10" - Right Hand - 3,500 lbs
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Search Results: brake controler
- Shop: Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Search Results: 44649
- Shop: Trailer Hitch
- Shop: Trailer Wiring
on Accessories and Parts
