Will the Bulldog High-Profile Coupler Latch Repair Kit Work on a Bulldog 2B Hammerblow Coupler

Question

Question:

I have a Hammerblow Bulldog coupler No 2B. Is the BD024200 the correct repalcement part?

asked by: Tom

0

Expert Reply:

There are several different styles of Bulldog 2B coupler latches. If your coupler has the high profile latch like the one on our Bulldog Collar-Lok Coupler w/ High-Profile Latch, item # BD028462, the Bulldog High-Profile Latch Repair Kit, item # BD024200, will be the correct replacement.

The other latch styles can be seen on the Bulldog Collar-Lok Coupler w/ Pin, item # BD028244, which utilizes a pin to secure the coupler to the trailer ball and the Bulldog Collar-Lok Coupler w/ Low-Profile Latch, item # BD028288, which utilizes a low profile cam style lever and pin to secure the coupler.

expert reply by: Robert G

0

Answer 1

Thanks for the photo; it looks like you have a low-profile latch and so the Replacement Coupler Cap Spring #BD500354 would work for your coupler.

view full answer...

Answer 2

There actually isn't any difference in strength for a straight tongue coupler, no matter if it is bolted on or welded on. Most couplers are designed to be one or the other, and their capacity won't change - and the security to your trailer -…

view full answer...

Answer 3

I'm assuming you have a Bulldog Collar-Lok trailer coupler like the #BD028244 you'd looked at. Blaylock makes a lock specifically designed for a Bulldog Collar-Lok trailer coupler, part #BLTL-20-40D. The lock includes the lock assembly itself…

view full answer...

Answer 4

Great news! The replacement spring you are looking for is the #BD500354. I have linked it to this page for your viewing and purchasing convenience.

view full answer...

Answer 5

It sounds like you have a Collar-Lok coupler such as #BD028244. For that type of coupler you could use lock #BLTL-23. The body is aluminum but the pin inside that goes way up into the coupler is steel. It fits 2-5/16 inch Collar-Lok couplers. For 2…

view full answer...

Answer 6

The HammerBlow Trailer Coupler, like the #BD028463 is a coupler that will mount to the from frame of a trailer and be used to attach to a hitch ball on the back of a vehicle. It mounts to 50 degree A-Frame Tongue and will couple to a 2-5/16 in hitch…

view full answer...

Answer 7

The inner dimensions of the Channel Tongue Trailer Coupler #CT-5003-Z are 5" from the bend to the rear of the coupler, 3-1/6" wide and 2-1/8" tall. I have created a diagram with these measurements below.

view full answer...

Answer 8

In your photo it looks like there could be a hitch ball hole in the cross brace on the back of your Chevy flatbed. If you can find a sticker or plate that indicates a tow rating, and a hitch ball of the appropriate rating and with the shank diameter…

view full answer...

Answer 9

If you have a single axle trailer with a 3,500-lb axle then your total weight capacity is 3,500-lbs with each wheel bearing 1,750-lbs. There should be a sticker or plate somewhere on the frame near the front of the trailer that lists the official…

view full answer...

Answer 10

Yes, the etrailer coupler part #CT-5003-Z is an exact replacement for the Ram coupler you have now. The mounting holes are the exact same dimensions.

view full answer...

Answer 11

Based on the model information from Dutton-Lainson coupler #DL13897 would have that pin and chain. For a similar model that does not have the pin and chain but is still rated the same and also fits a 2 inch ball and 3 inch tongue use #CT-5003-Z. I…

view full answer...

Answer 12

Yes, the mounting holes for the Channel Tongue Trailer Coupler #CT-5003-Z measure 1" from the center down to the bottom of the channel.

view full answer...

Will the Bulldog High-Profile Coupler Latch Repair Kit Work on a Bulldog 2B Hammerblow Coupler

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching