Availability of Threaded Gooseneck Hitch Ball with 2 inch Diameter Shank

Question

Question:

Hello. Ive got a 2007.5 2500 hd Chevy silverado. It has a gooseneck plate, running under the oem box. It has a 2inch thread opening for the gooseneck ball shank. Are your products able to thread into this plate?

asked by: David C

0

Expert Reply:

The gooseneck ball part # BWHB94009 that you referenced does have a 2 inch diameter shank like what you said you need. Do you need a coarse thread? If so this will work well as it is a 2 inch diameter shank with coarse threads.

expert reply by: Jameson C

0

Answer 1

In order to install a fifth wheel hitch in your 1996 Ford F-250, you will need a set of base rails like part #RP30035. The first rail will sit 32-1/2 inches from the rear edge of the truck bed. You will then use the fifth wheel itself to position the…

view full answer...

Answer 2

The manufacturer and model number of the pin box is usually printed on a sticker or stamped into a plate or directly into the metal of the pin box. If you can't find that, the manufacturer of your 5th wheel should be able to tell you which pin…

view full answer...

Answer 3

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 4

As a general rule, when towing a gooseneck trailer with a regular bed pickup truck, you will want at least 4-6 inches of clearance from the top of the bed rails to the trailer. I first recommend determining the distance from the base of the truck bed…

view full answer...

Answer 5

For your Fabex 765 pin box on your 2008 Cameo 5th wheel, I recommend the 5th Airborne Premium Fifth Wheel Air Ride Coupler #5AB-E510-710 or the Trailair Air Ride 5th Wheel King Pin #UF35-946212. These are the only 21K pin box replacements we have for…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Availability of Threaded Gooseneck Hitch Ball with 2 inch Diameter Shank

Product Page this Question was Asked From

Continue Researching