Tips for Removing Pine Tree Sap from Tonneau Cover

Question

Question:

How do i get pine sap off tonna cover

asked by: Lillian K

0

Expert Reply:

My Truxedo representative recommends using hot water, car wash soap and a soft bristle brush to remove that sap. It's going to take some elbow grease, but that should remove it. Once you have the sap removed, Truxedo recommends using their Pro-Tex protectant spray, part # TX1704511 to provide a layer of protection that will prevent sap from sticking next time.

expert reply by: Jameson C

0

Answer 1

I went ahead and did some research, and I discovered that the replacement tarp depends on what model of TruXedo cover you have on your 2008 Toyota Tacoma's 5-Foot Bed. From my research, it is possible that you have one of three different covers.…

view full answer...

Answer 2

The Craftec Hatch-Style Tonneau Cover, part #352128 is a one-piece lightweight tonneau cover, and has two hidden latches at the rear so you will not have a problem with it flapping in the wind when installed on your 2000 Dakota. The tonneau cover…

view full answer...

Answer 3

We do have the slide-in strips for 6-1/2 foot beds you are looking for; you will need the Replacement TruXedo Shur-Bond Hook-And-Loop Fastener Strips #TX1117876 which is 80 inches long.

view full answer...

Answer 4

I contacted TruXedo, and they informed me that the Replacement Rear Support Bow #TX5976-RearBow is 58-3/4" long.

view full answer...

Answer 5

Yes, to replace the rail end caps for the TruXedo Lo Pro Tonneau Cover #TX555901 on your 2006 Tacoma you will need part #TX1118097 for the Right Side and #TX1118096 for the Left Side. These are direct replacement parts and will work perfectly with…

view full answer...

Answer 6

We carry so many varients of tonneau covers for the different vehicles. The options we carry for your 2005 Toyota Tacoma would be the TruXport, Lo Pro or the Deuce 2. Of those three, we have one replacement tarp and that is the replacement tarp for…

view full answer...

Answer 7

I may have a solution for you, but it will be difficult to confirm a correct replacement TruXedo Tonneau Cover for your 2005 Toyota Tacoma without identifying information such as a model number. I do show a few TruXedo Tonneau Covers that are custom…

view full answer...

Answer 8

The replacement tarp part #TX1117750 is the correct replacement tarp for a Lo Pro Tonneau for a 2009 Toyota Tacoma with a 6 foot bed since this tarp fits the part #TX556901 which fits your truck.

view full answer...

Answer 9

The part number on that sticker in your photo refers to the tensioning device, but luckily that narrowed things down enough to determine that the #TX1115174 Velcro strip is the correct replacement for you. It's longer than you actually need, but…

view full answer...

Answer 10

I went to our warehouse and took a look at the Replacement Header Seal for TruXedo Lo Pro QT, part #TX1704787. You will need to remove the seal you currently have by removing the plug on the end of the header. You may need to use something like a…

view full answer...

Answer 11

The TruXedo Shur-Bond Replacement Velcro #TX1115174 does fit the Lo Pro QT tonneau covers but measures more than 1-inch wide; it is 1-5/16-inches in width and 80-inches long. This slides into the cover's rail. We also have a screw-on Velcro strip…

view full answer...

Answer 12

For your short bed truck that has a Truxedo Lo Pro QT you would want the part #TX1115174 for replacement Velcros strips.

view full answer...

Tips for Removing Pine Tree Sap from Tonneau Cover

Product Page this Question was Asked From

Continue Researching