Replacement Screw And End Cap For TracRac Ladder Rack

Question

Question:

What is the screw type and size needed for end cap. Lost cap and screw Replacement End Cap for TracRac Ladder Racks TracRac Accessories and Parts 7 reviews Code: TA01-27023

asked by: Jason

0

Expert Reply:

I reached out to my contact at Thule the maker of TracRac and the Replacement End Cap for TracRac Ladder Racks # TA01-27023 uses an M6-1 socket head cap screw. We carry only one screw this diameter and head and it is the # TH919063054 which is 30mm long. If you need a different length, you will need to obtain it at a local hardware store.

expert reply by: Jason S

0

Answer 1

Replacement End Cap for TracRac ladder racks #TA01-27023 does not come with the set screw. If the old screw is missing you would need to obtain one from a local hardware store.

view full answer...

Answer 2

It sounds like you are looking for replacement end caps for the ends of the bars on your TracRac ladder rack. For a single replacement use #TA01-27023. It will fit TracRac G2, T-Rac G2, and TracONE truck bed ladder racks.

view full answer...

Answer 3

The Replacement Crossbar for TracRac Ladder Racks - 69-1/2" Long - Qty 1 #TAFX-30007-02 compatible with your SR rack will use the end cap #TA01-27023. This threaded end cap will replace your missing end caps. The screw you will need for this…

view full answer...

Answer 4

For M8 hex nuts to go with the Replacement Socket Head Cap Screw #TH919063054 we have the #185917.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Replacement Screw And End Cap For TracRac Ladder Rack

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching