Replacement Socket Head Cap Screw for Thule Fit Kits and Ski Carriers - M6 x 30

See what our Experts say about this Thule Accessories and Parts

• Replacement Locking Bolt for Thule Podium Foot
  We do have a wide variety of replacement parts available for Thule products. Without being able to see the part, it sounds to me like you might be looking for the Replacement Socket Head Cap Screw # TH919063054 which works on Thule Fit kit packs and ski carriers. If you can send me a picture of the part you're looking for, I can help you find an appropriate replacement.
  view full answer...
• Replacement Parts Needed to Install Older Thule Hullavator 897XT In Crossbar T-Slots
  To get replacement T-Slot hardware for your older model 897XT Thule Hullavator carriers you need the following parts (4 per Hullavator system): - Square Nut # 853-7557 - M6 x 30 Socket Head Cap Screw # TH919063054 - M6 Washer # 951061254 I've attached a clip from the original instructions showing how these parts should be installed in a T-Slot crossbar for your reference.
  view full answer...
  
• Will Older 897XT Thule Hullavator Install on Yakima JetStream Crossbars
  Yes, the older Thule Hullavator (897XT) will fit Yakima JetStream bars. You'll use the T-Slot mounting hardware that would have come with the older model carrier and then you need to make sure you can move the carrier out far enough that there is 4" of clearance between the arms and your vehicle when the Hullavator is in the "load" position per the instructions. If you don't have that mounting hardware anymore then you need the 4 of each of the following parts: Socket Head Cap Screw -...
  view full answer...
• M8 Nuts that Fit M8 Thule Bolt # TH919063054
  For M8 hex nuts to go with the Replacement Socket Head Cap Screw # TH919063054 we have the # 185917.
  view full answer...
  
• Replacement Hardware To Mount Thule Hullavator Onto Malone Crossbar Top Channel
  You will need 8 of the Replacement Socket Head Cap Screw M6 x 30 # TH919063054 and 8 of the Replacement Square Nut # 853-7557. This will allow you to install the Thule Hullavator onto various crossbars with the T-slot channel, including the Malone # MPG216.
  view full answer...
• How to Mount Older Thule Hullavator Into T-Slots of Crossbars
  From my understanding you should just need the M6 x 30 Socket Head Cap Screw # TH919063054, the M6 Washer # 951061254, and the Square Nut # 853-7557 for installing the older Hullavator into the T-Slot of a crossbar system. This stuff should have come with the Hullavator and I'm not aware of the need for a adapter to mount it in the T-Slot.
  view full answer...
• TracRac End Cap and Screw Replacement for TracRac Sliding Rack Crossbar
  The Replacement Crossbar for TracRac Ladder Racks - 69-1/2" Long - Qty 1 # TAFX-30007-02 compatible with your SR rack will use the end cap # TA01-27023. This threaded end cap will replace your missing end caps. The screw you will need for this is an M6-1 socket head cap screw # TH919063054 which is just over 1 inch long.
  view full answer...
  
• How To Install Older Thule Hullavator 897XT Onto Yakima Jetstream Crossbars
  Luckily your older Thule Hullavator is compatible with Yakima Jetstream Crossbars. You will need to use the hardware that came with the Hullavator to install it into the T-slot channel on top of your crossbars. If you don't have this hardware then you will need M6 x 30 # TH919063054 (qty of 8) and Replacement Square Nut # 853-7557 (qty of 8).
  view full answer...
• Hardware for Replacement End Cap and Cleats for TracRac Ladder Racks
  We have socket head cap screw # TH919063054 that is the right size for the Replacement End Cap for TracRac Ladder Racks # TA01-27023. Another Expert found that in order to install the Replacement Tie-Down Cleat # TA01-27046 you are going to need 1/4"-20 x 1-3/4" socket head cap screws. We do not carry this screw separately so you would need to source it from your local hardware store.
  view full answer...
• Correct T-Track Mounting Hardware for the Thule Hullavtor
  The replacement bar mount assembly just includes the bar mount, you'd still need the mounting hardware, so you will need 8 of the Replacement Socket Head Cap Screw for Thule Fit Kits and Ski Carriers # TH919063054 and 8 of the Replacement Square Nut for DeWalt Contractor Series Ladder Racks or Thule Roof Mounted Bike Carriers # 853-7557. This will allow you to install your Thule Hullavator onto various crossbars that have t-tracks so you do not need to move your entire setup from vehicle...
  view full answer...
• Do You Carry Spare Parts for the Thule Hullavator # TH898?
  While Thule unfortunately does not make a complete parts bag for the Thule Hullavator # TH898 anymore, we do have individual replacement parts available for purchase. For instance, if you need a replacement M6 socket screw, that is the Replacement Socket Head Cap Screw for Thule Fit Kits and Ski Carriers - M6 x 30 # TH919063054. Feel free to respond with what individual replacement parts you need, and I will be happy to point you in the right direction.
  view full answer...
• Parts to Install Older Thule Hullavator TH897XT on Thule WingBar Crossbars
  In order to install your older Thule Hullavator TH897XT the Thule aero WingBars, you are correct that an M6 x 30 is needed, as well as the nut and a washer. The exact parts are as follows: - Replacement Socket Head Cap Screw - M6 x 30 # TH919063054 - Replacement Square Nut # 853-7557 - Replacement M6 Washer # 951061254
  view full answer...
• Replacement Screw And End Cap For TracRac Ladder Rack
  I reached out to my contact at Thule the maker of TracRac and the Replacement End Cap for TracRac Ladder Racks # TA01-27023 uses an M6-1 socket head cap screw. We carry only one screw this diameter and head and it is the # TH919063054 which is 30mm long. If you need a different length, you will need to obtain it at a local hardware store.
  view full answer...

Do you have a question about this Accessories and Part?