Replacement Hub Recommendation for Hub Stamped 8-219
Question:
The hub I need says: 8-219 MTA6 340 I really need lugs and lug nuts but will take entire hub.
asked by: Jeff C
0
Expert Reply:
Since you said your hub says 8-219 that would indicate that you need the Dexter hub part # 8-219-13UC3 as a replacement. This is a hub for higher capacity axles between 5,200 and 7,000 lbs and has a bolt pattern of 8 on 6-1/2 inches.
expert reply by:
Jameson C
0
Product Page this Question was Asked From
Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Pre-Greased
- Standard
- 25580
- 14125A
- For 5200 lbs Axles
- For 6000 lbs Axles
- For 7000 lbs Axles
- 9/16 Inch Stud
- 8 on 6-1/2 Inch
- 16 Inch Wheel
- 16-1/2 Inch Wheel
- 17 Inch Wheel
- 17-1/2 Inch Wheel
- Dexter
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Dexter Trailer Hub & Drum for 5,200- to 7,000-lb Axles - 8 on 6-1/2 - 9/16" Studs - Pre-Greased
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb E-Z Lube Axles - 12" - 8 on 6-1/2
- Article: Overview of Lubricating Grease
- Video: Trailer Brakes and Wiring Installation
- Shop: Dexter Trailer Hub and Drum Assembly for 5,200-lb to 7,000-lb Axles - 12" - 8 on 6-1/2
- Shop: Dexter Trailer Hub and Drum Assembly - 7K lb E-Z Lube Axle - 12" - 8 on 6-1/2 - 1/2" Studs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Trailer Hub and Drum Assembly - 5,200-lb to 7,000-lb Axles - 8 on 6-1/2 - Oil Bath
- Shop: etrailer Electric Trailer Brakes - 12" - Left/Right Hand Assemblies - 5,200 lbs to 7,000 lbs
- Search Results: dexter 5200
- Search Results: 16 inch load range g
- Search Results: axel grease
- Search Results: ez lube spindle
- Search Results: bearing buddy 2717
- Search Results: ez lube bearing kit
- Search Results: 110 psi rims
- Q&A: How to Measure for Selection of the Correct Bearing Buddy Bearing Protectors
- Q&A: What Is The Recommended Lug Nut Torque On 7,000lb Axles?
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub
- Video: Remove, Inspect, and Reinstall Trailer Bearings, Race, and Seals Demonstration
- Video: Choosing the Right Brake Controller
- Q&A: How to Install Races in a Hub Assembly
- Q&A: Suspension Enhancement For a 2021 Grand Design Momentum 353G With 7,000LB Dexter Axles
- Shop: Brake Controller
- Q&A: Troubleshooting Newly Installed Self-Adjusting Brake Not Working Properly
- Q&A: How to Adjust Self-Adjusting Trailer Brakes
- Q&A: Do Self-Adjusting Trailer Brake Assemblies have to be Initially Adjusted
- Video: Bearing Repacking and Grease Seals Installation
- Video: etrailer Trailer Bearings Races Seals Caps - Races - 25520 Review