RV Trailer Hitch Fit for 68 inch Wide I-Beam Frame

Question

Question:

Do you have an RV hitch that will fit my travel trailer with an I frame that is 68 inches wide ? Either bolt-on or weld is OK...thanks,

asked by: Gary W

0

Expert Reply:

The Curt hitch part # 13703 is our most popular RV hitch because of how wide of a range of trailer it can fit. It can fit I-beam trailers that are between 22 and 72 inches from outside to outside so your that is 68 inch would work well.

expert reply by: Jameson C

0

Answer 1

The Adjustable Width Trailer Hitch Receiver for RVs, 22" to 66" Wide, #C13704 has brackets that will mount to the bottom of the frame. The square tubing sets within these brackets which extend toward the inside of the frame. If you…

view full answer...

Answer 2

In order to satisfy Curt warranty requirements, any of their Class I or II receivers (like the C11423 you referenced) as well as a few of their Class III hitches must be used with a stabilizing strap like part #18050. This applies to any…

view full answer...

Answer 3

The Furrion AC/DC Distribution Panel will work to replace the WFCO WF-8930/50 distribution panel but is not considered an exact replacement. We do not carry a distribution panel that is an exact replacement for that WFCO model but the Furrion will…

view full answer...

Answer 4

I wouldn't be able to comment on the frame strength but we do have trailer hitch options which can handle the tongue weight load you are looking carry. The best option we have for this would be the Draw-Tite Ultra Frame Service Body Trailer Hitch…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

RV Trailer Hitch Fit for 68 inch Wide I-Beam Frame

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching