Components Needed To Add Brake Controller To 2010 Nissan Pathfinder With 4-Way Trailer Connector
Question:
I saw a video for 39510 It looks like this is for a 2011 Nissan Pathfinder, will the same information work for the 2010 pathfinder with an existing 4 pole connector? Ive checked under the hood and I have a spot for a relay and under the dash, Ive got a harness, I just want to make sure the one in the video will work for the 2010 model. Also the portion about clipping off an existing clip to wire the 12v and brake controller from the 7 pin to the existing wiring is the same. This looks like a fairly simple installation, I just want to ensure the 2011 and 2010 pathfinders are laid out the same and if the same part numbers will work. Thanks,
asked by: Casey
Expert Reply:
The Video you said you have watched for the Tekonsha Voyager, part # 39510 will be the same for your 2010.
As the video shows you will also need part # 3050-P for the plug-in harness. One end plugs into the back of the brake controller and the other end plugs into the port located under the dash by the diagnostic port.
You will need part # ETBC7 which will have the duplex wiring and but connectors you need to complete the installation as shown in the attached video. You will also need the Curt Relay Kit, part # C57000. This will have the brown relay you need for 12V power as shown in the video. The relay is not available as a separate item.
For the electrical connections I recommend dielectric grease like part # 11755. This keeps moisture and dirt out of the connections.
Products Referenced in This Question
Dielectric Grease for Electrical Connectors, 2 oz.
- Accessories and Parts
- Trailer Wiring
- Wiring
- Dielectric Grease
- LubriMatic
more information >
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Curt Relay Kit for Nissan Armada or Titan Aftermarket Tow Package
- Accessories and Parts
- Trailer Wiring
- Relays
- CURT
more information >
Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Voyager Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Manual Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- Indicator Lights
- Up to 90 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Trailer Wiring Diagrams
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Comparing the Curt Q20 and the Curt A20 5th Wheel Hitches.
- Q&A: How To Add a Fuel Tank To a Truck with 5th Wheel Hitch In Bed
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Guide to Choosing the Best Truck for 5th-Wheel Towing
- Q&A: Kit to Convert 2021 Vanleigh Pinecrest 335RLP to Electric Over Hydraulic Disc Brakes
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Best Camper Jacks
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Article: Brake Controller Installation: Starting from Scratch
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)