Hitch Fit for Rear of Rockwood ROO 23IKSS

Question

Question:

I have a rockwood roo 23ikss. I beam with stabilizers on the end. DO you have a hitch for this model?

asked by: Al

0

Expert Reply:

The Curt Hitch part # 13703 would be the best option we offer as it can fit I-beam trailer frames that are between 22 and 72 inches apart outside to outside.

I attached an install video for the hitch as well. This would need to install on the I-beam portion of the frame and not on the bumper stabilizers.

expert reply by: Jameson C

0

Answer 1

If your RV currently has incandescent lights and you're going to be adding the Triple LED #CE44VR to the mix then you will most likely need to add resistors like the Load Resistor Kit for LED Turn Signals - 50 Watts - 6 Ohm - Qty 2 #DI34ZR to…

view full answer...

Answer 2

Installing load resistors on the trailer's wiring like the #DI34ZR will prevent the flickering of the taillights if you wanted it to stop. If you can live with the flickering though there's no reason you'd have to do this. The…

view full answer...

Answer 3

Each bulb should have a power wire and a ground wire. As you can see in the diagram I provided, one lead of the resistor is tapped into the power wire, and the other lead of the resistor can either ground to the vehicle or tap into the ground wire…

view full answer...

Answer 4

The Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras #FCE48TASL-05 can either be powered by the running lights (which is why you have to physically turn yours on) or off of the reverse lights, which means it would…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 8

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Hitch Fit for Rear of Rockwood ROO 23IKSS

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching