Where Would Brake Controller Install Port be On a 2016 Ram 1500 If Equipped
Question:
Cant find under dash. Has 7 pin plug in rear.Doesnt have tow package. Dealer says truck didnt come with plug for after market brake controller. Wants 400 bucks to install.
asked by: Jim W
Expert Reply:
If your truck is going to have the pig tail harness needed to install the # 3024-P harness it will be right above the where your right foot would be covered in a foam tape.
Sometimes, these harnesses do not end up in the same exact location on every vehicle of the same model. The connector may be hidden and you may have to do a bit of searching to find the right connector. We have had pickups in for installations where the brake controller harness connector was hidden out of sight up under the dash.
If not you could hardwire the controller with the # 5506. Since you have a 7-Way you will only need a few more components to complete a brake controller install on your vehicle.
Next, for a wiring kit to install the brake controller and the 7-way adapter you would want the Wiring Kit for 2 and 4 Brake Electric Brake Controllers # 5506. This will provide the power source and ground for the wiring for the brake controller. You will need to test the wires from the brake pedal switch of your vehicle to find a circuit that has voltage when the brakes are applied and none when not applied. This will be the circuit you will run the red wire to.
Finally you will need to run a length of 10 gauge wire (part # 10-1-1) from the brake output circuit of the controller to the brake output circuit of the 7-way (blue wire). The # 10-1-1 is sold by the foot so you will need to order a quantity of the amount of feet you will need.
Products Referenced in This Question
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Ram
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Wiring Kit for 2, 4, 6, and 8 Brake Electric Trailer Brake Controllers
- Accessories and Parts
- Trailer Brake Controller
- Installation Kits
- etrailer
more information >
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Brake Controller Installation: Starting from Scratch
- Article: Trailer Wiring Diagrams
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Installing an Electric Brake Controller on 2007-2013 GM Full-Size Truck or 2007-Present GM SUV
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Install a Brake Controller on Chevrolet / GMC 1999-2006 Pickups
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: Does the Tekonsha P3 Trailer Brake Controller Turn Off or Stay On All the Time
- Q&A: Parts Needed To Install A Brake Controller On A 2023 Freightliner Cascadia
- Q&A: How Does Brake Controller Install on Freightliner S2RV Chassis
- Q&A: Parts Needed to Add 7-Way & Brake Controller on 2023 Kia Sportage
- Q&A: Replacement Lid and Lift Arm for Dometic 810263
- Q&A: Wiring Configuration for Tekonsha Prodigy P3 Trailer Brake Controller 90195