Dimensions of the Fulton Coupler # F44305R0317

Question

Question:

Just needed to know overall size to see if it matches what I have

asked by: Kevin

0

Expert Reply:

The Fulton coupler # F44305R0317 that you referenced has the standard 50 degree angle for mounting to the trailer frame and overall is 12-1/4 inches long and 11-1/4 inches wide.

expert reply by: Jameson C

0

Answer 1

The two couplers you referenced are identical size-wise. The #DM15000-52 is a bolt-on application with the EZ latch system and a silver finish. The DM12563 uses a standard latch, is a weld-on application and has a red finish. For the #DM15000-52, the…

view full answer...

Answer 2

The eZ-Latch on the Demco Channel Tongue Trailer Coupler #DM13689-52 does make it easier to connect the trailer and ensure the coupler latches down fully than your trigger style coupler. Since you can visibly see the latch raise and drop you know you…

view full answer...

Answer 3

I am certainly glad you are taking safety into consideration when trying to choose your coupler, although none of the Demco couplers would be considered "safer" than the others you mentioned. Among the Demco Channel Tongue Trailer Coupler -…

view full answer...

Answer 4

The Fulton Fas-Lok Coupler - 2" Ball - 3" Channel - 6,000 lbs #F346000301 you referenced has a 2 inch ball and fits a 3 inch channel. The holes are measured on center at 3 inches apart. The holes will be 1 inch on center from the top and…

view full answer...

Answer 5

Actually, if the latching portion of the coupler still works correctly, you can simply engage the manual lockout lever on your coupler which will prevent the coupler from compressing and trying to apply the brakes, allowing you to continue using your…

view full answer...

Answer 6

The standard, basic straight tongue coupler I have that will fit a 3 inch channel, and a 2 inch ball with a 6,000 lbs. weight capacity is the Fulton Fast-Lok Coupler with Cast Ball Clamp, 2 Inch Ball, 3 Inch Channel - 6,000 lbs, part #F346000301. It…

view full answer...

Answer 7

As long as the tongue on your trailer is 3 inches wide, the Fulton Fast-Lok coupler will work fine for you. There is nothing wrong with a little overkill. Keep in mind that the higher weight rating of coupler will not increase the weight rating of…

view full answer...

Answer 8

The Fulton Fas-Lok Coupler - 2" Ball - 3" Channel - 6,000 lbs #F346000301 will not be under the ball all the way to the hitch ball shank but it will be on the under side of center. It is possible for a latch to be installed incorrectly and…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Dimensions of the Fulton Coupler # F44305R0317

Product Page this Question was Asked From

Continue Researching