Does Using a Hitch Adapter Change the Hitch Tongue Weight Capacity
Question:
I have a 2009 Honda Accord I have a hitch on the car that has a 1 1/4 inch receiver. I have added a piece of equipment to change it to a 2 inch receiver what is the torque weight that the car can handle or the hitch can handle?
asked by: Becjy
Expert Reply:
Using a hitch adapter like the one shown in the photo you provided will lower the tongue weight of your existing hitch by 50 percent. The Class I hitch on your 2009 Accord would normally have a tongue weight capacity (maximum amount of downforce that can be applied to the hitch without causing damage) of 200 lbs. Because using the adapter moves the load further away from the hitch, more leverage will be applied to the hitch, so using the adapter lowers the tongue weight capacity to 100 lbs. This means that the weight of the bike rack you're using plus the combined weight of the bicycles on the rack cannot exceed 100 lbs.
Exceeding that capacity can cause the hitch to bend or break, or cause the hitch attachment points to the vehicle to fail.
Honestly, your best course of action would be to avoid using the adapter, and use a bike rack that's designed to be used with a Class I hitch. Swagman makes high quality but reasonably priced hitches like the Trailhead, part # S63360 that can be used in both 1-1/4 and 2 inch hitches.
The bike rack and hitch manufacturers both agree that no more than two bikes should be carried in a rack used on a Class I hitch. Additional bikes would increase the leverage applied to the hitch, like I mentioned above.
Products Referenced in This Question
Swagman Trailhead Bike Rack for 2 Bikes - 1-1/4" and 2" Hitches - Tilting
- Hitch Bike Racks
- Hanging Rack
- Folding Rack
- Tilt-Away Rack
- Frame Mount
- Locks Not Included
- 2 Bikes
- Class 1
- Class 2
- Class 3
- Fits 1-1/4 and 2 Inch Hitch
- Fits 1-1/4 Inch Hitch
- Fits 2 Inch Hitch
- Swagman
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Video: etrailer Trailer Hitch Receiver Adapter And Extender Review
- Shop: Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver
- Shop: Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2"
- Shop: Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver with 5" Rise
- Shop: Trailer Hitch Adapter - 1-1/4" to 2" Hitch - 4-1/2" Drop/5" Rise - 6-1/2" L
- Shop: etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 44649
- Video: Choosing the Right Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Wiring
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Search Results: 68149
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Shop: Brake Controller
- Search Results: 25580
- Q&A: Recommended Replacement for Atwood Surge Brake Actuator 85778
- Video: Choosing the Right Brake Controller
- Article: Trailer Wiring Diagrams
- Shop: Fifth Wheel Hitch
- Q&A: Location of the 40-Amp Fuse for the 2006 Chevrolet Silverado Tow Package
- Search Results: dust cap
- Shop: Gooseneck Hitch
- Article: My Trailer Hitch Doesn't Fit
- Video: etrailer Hitch Pin Alignment Collar Review
- Q&A: Fuse Location for Trailer Brake Controller on a 2005 Chevy Silverado
- Search Results: led turn signal
on Trailer Hitch
