Trailer Hitch and Wiring Recommendation for a 2015 Toyota Highlander
Question:
I am looking at putting a hitch on my 2015 highlander. Ive reviewed the QandA on your website which was very helpful. I think Im going to go with the Curt hitch, but have a wiring question. It looks like once you attach the wires, theyd sit coiled in the trunk and be closed in the tailgate when in use rather than being permanently run and mounted to the hitch, is this correct? Is there an aftermarket wiring harness that would be permanently attached outside of the car?
asked by: Adam K
Expert Reply:
It may seem counter-intuitive at first, but having trailer wiring that stores on the interior of a vehicle is actually a good thing. This prevents corrosion from accumulating in the connectors and reduces the chance of the trailer wiring getting damaged by a rock or something under the vehicle.
The door seal of the vehicle is thick enough that it would not damage the wiring after you pull the harness out and close the door on it.
For Curt wiring you would want the part # C56217. For a hitch you would then want the part # C13200.
If you wanted to do some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include a ball mount with the right rise or drop to tow the trailer level, check out the link I have included that explains how to measure to choose a ball mount to tow the trailer level.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 900 lbs TW
- 6000 lbs GTW
- 8000 lbs WD GTW
- 2 Inch Hitch
- 900 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Choose the Right Trailer Hitch Class
- Article: Troubleshooting 4 and 5-Way Wiring Installations
- Q&A: How to Tell if 2019 Toyota Highlander Has Factory Tow Package
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Brake Controller Wiring for Ford E-450 Motorhome
- Q&A: Replacement 1998 PJ Utility Trailer Hub with QRG 3G and 84000 Stamped Into Hub
- Q&A: Is the Curt Trailer Hitch Receiver Fascia Trim Diagram Correct for 2022 Ford Bronco Sport
- Q&A: Installation of the OEM Replacement Tow Wiring for 2020 Toyota Highlander
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: How to Determine if a 2017 Toyota Highlander has a Factory Tow Package
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Correct Noise from Exhaust Rattling Against a Trailer Hitch
- Article: How to Measure for Trailer Hitch Drop