Is Mounting Hardware Included with Ultra-Fab Electric A-Frame Jack # UF38-944037

Question

Question:

Is needed hardware to install jack included?

asked by: Sara

0

Expert Reply:

You will source your own hardware for installation of the Ultra-Fab Electric A-Frame Jack # UF38-944037 on your a-frame trailer. Grade 5 stainless steel hardware is recommended and the mounting flange has two hole patterns for convenient fit with 2-inch or 2-1/4-inch hole spacing on your trailer frame.

expert reply by: Adam R

0

Answer 1

The difference would be the collar length that comes range hood vent. The part #V2111-13 has a collar length that is 1-3/4 inches in length and then the part #V2111-03 has one that is 5/8 inches in length. The collar length needed is going to be…

view full answer...

Answer 2

Trailer makers rarely keep track of smaller items like vent parts used in fabrication of their trailers so finding the right replacement part is often just a matter of measuring, as you have done. Since we do have this item in stock, Ventline…

view full answer...

Answer 3

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 4

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 5

The squeaking noise on your trailer is probably coming from the joints in the suspension creating metal to metal friction. So, unless your original Equa-Flex Cusioned Equalizers are damaged or corroded, what will make the biggest difference is to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 10

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Is Mounting Hardware Included with Ultra-Fab Electric A-Frame Jack # UF38-944037

Product Page this Question was Asked From

Continue Researching