How Does the Spindle Seal Set part # BB60003 Install

Question

Question:

On the seal saver installation video it shows the o rins going on after the stainless shoulder ring,is it not acceptable to install the rings beforeinside the ss shoulder rings?Also if installed like in the video what keeps the rings in place?

asked by: Gerry B

0

Expert Reply:

I attached a picture that shows a diagram for how the Spindle Seal Set part # BB60003 would install on a spindle. Installing the shoulder ring first gives the O-ring something to press against so that it can seal better. Reversing the order would defeat the purpose.

I attached the demo video you referenced as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

We do have a compatible grease seal for your 168255TC oil seal, however, we do not carry rubber coated seals in this size. The 168255TC oil seal was designed to work with oil bath hubs on a 3,500 lb axle. For the most part, axle manufacturers have…

view full answer...

Answer 2

While tinned wiring is the norm when it comes to interior wiring on boats, boat trailers see a minimal amount of water compared to the actual boats. They do use a tin coating on the pins that are the parts of a wiring harness like the Wesbar 5-Pole…

view full answer...

Answer 3

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 4

Ff the springs you are installing are 25-1/4 inches, you would need to place the hangers between 24-3/4 and 25 inches apart. The shackle should be angled as the drawing shows in the attached helpful article, which should be toward the rear of the…

view full answer...

Answer 5

The shackle straps need to be placed on the outside of the rear leaf spring hangers which you can see in the attached photo. Furthermore, the distance between the two mounting plates (inside to inside) on your leaf spring hangers should be…

view full answer...

Answer 6

The hangers that come with the Single-Axle Trailer Hanger Kit for Double-Eye Springs #APS2 that you referenced are wide enough to fit a 1-3/4 inch wide leaf spring as that's what they are designed to fit.

view full answer...

Answer 7

For your single axle boat trailer, I recommend the Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 along with the 3-Leaf Double-Eye Spring for 2,000-lb Trailer Axles - 23-1/2" Long #SP-113275.…

view full answer...

Answer 8

The Single-Axle Trailer Hanger Kit for Double-Eye Springs - 1-1/2" Front, 1-1/4" Rear #APS2 will work well for your 1-3/4 inch wide leaf springs. Double eye springs are the style have both the bolt in the front and rear and are more common…

view full answer...

Answer 9

I recommend the Single-Axle Trailer Hanger Kit for Double-Eye Springs #APS2. With the double eye leaf spring you will need to add shackle straps to allow the leaf spring front to back movement when compressing. While the CE Smith Front Hanger Bracket…

view full answer...

Answer 10

In order to switch from slipper to double eye springs you'll need new hangers which are going to dictate your height so if you're looking to maintain the same height, you'd want to choose new hangers which are the same height as your…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

How Does the Spindle Seal Set part # BB60003 Install

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching