Brake Line Kit Recommendation for Dexter Brake Assemblies 23-398 and 23-399

Question

Question:

Will item number 20TA-BLKIT fittings be compatible with Dexter drum brake numbers 23-398 and 28-399? It says it works great with disc brakes so I want to be sure the fittings are the same between disc and drums.

asked by: Chris

0

Expert Reply:

Trailer brakes use the same thread size whether they are disc or drum. The Kodiak Hydraulic Brake Line Kit # 20TA-BLKIT that you referenced would work well with the Dexter drums # 23-398 and # 23-399.

expert reply by: Jameson C

0

Answer 1

The wires of the breakaway switch part #K71-691 are 14 gauge. The difference between it and the Dexter breakaway kit part #N65113 is that Bargman makes the N65113 and Esco makes the #K71-691. the Esco one is only one made in USA. They will function…

view full answer...

Answer 2

The Titan BrakeRite EHB Electric-Hydraulic Actuator for Disc Brakes part #T4813100 will need to receive power from a 12 volt battery with a 40 amp circuit breaker like part #9510 placed 6" from the positive battery terminal. I have attached…

view full answer...

Answer 3

The blue brake controller output voltage wire extends from the factory connector under the dash and terminates in the engine compartment near the fire wall. Due to the cramped quarters in the engine bay, This wire is very hard to locate. Our…

view full answer...

Answer 4

Yes, there is one option for replacement breakaway switch that is made in the U.S.A., which comes from Dexter Axle: - Replacement Breakaway Switch with Cable and Pin for Dexter Trailer Breakaway Kit #K71-691

view full answer...

Answer 5

If your towing setup requires the 12 volt power circuit to be active (not all do), it would need to be ran to the positive post of the CR-V battery through a circuit breaker like part #9510. This prevents the amperage draw of the circuit from ever…

view full answer...

Answer 6

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 7

Here is what you will want to do. Since your 12 volt accessory circuit is only rated for 20 amps you are going to want to run a 10 gauge wire like the part #10-1-1 (sold by the foot) from the positive battery post of your vehicle through a 40 amp…

view full answer...

Answer 8

I took a look at what we have, and the only thing I was able to find was the Hydrastar Hydraulic Brake Line Kit #HS496-252, which measures 25' long. I also took a look at your 2019 Heartland Torque Travel Trailer Toy Hauler, and wanted to…

view full answer...

Answer 9

I believe what you mentioned is a standard way of running trailer brake lines on a tandem trailer. I attached a diagram for the brake line kit part #18TA-BLKIT and how it normally connects to a trailer. The main feed line runs to the first axle where…

view full answer...

Answer 10

I can help you correctly run hydraulic lines on your trailer. Adding disc brakes is a great idea, but the reason you are having such difficulty finding a schematic is because hydraulic brakes are rarely installed on 5th wheel trailers and they are…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Brake Line Kit Recommendation for Dexter Brake Assemblies 23-398 and 23-399

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching